User manual ASUS P5BV-C2L

[. . . ] SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi P5BV-C2L/WiFi-AP specifications summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] By default , the pin labeled "Chassis Signal" and " Ground" are shorted with a jumper cap. Remove the jumper caps only when you intend to use the chassis intrusion detection feature. P5BV-C2L/WiFi-AP R Chassis intrusion connector (4-1 pin CHASSIS) CHASSIS GND Chassis Signal +5VSB_MB (Default) P5BV-C2L/WiFi-AP Intrusion Connector 9. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC`97 audio standard. Connect one end of the front panel audio I/O module cable to this connector. P5BV-C2L/WiFi-AP Azalia-compliant pin definition AGND PRESENSE# MIC2_JD HP_HD Legacy AC'97-compliant pin definition AGND NC NC R AAFP MIC2_L MIC2_R HP_R Jack_Sense HP_L MIC2_L MIC2_R Line out_R NC Line out_L P5BV-C2L/WiFi-AP Front Panel Audio Connector · · We recommend that you connect a high-definition front panel audio module to this connector to avail of the motherboard's high-definition audio capability. By default, this connector is set to HD Audio. ASUS P5BV-C2L/WiFi-AP NC 1-35 10. ATX power connectors (24-pin EATXPWR, 4-pin ATX12V) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. ATX12V P5BV-C2L/WiFi-AP EATXPWR Ground +5 Volts +5 Volts +5 Volts -5 Volts Ground Ground Ground PSON# Ground -12 Volts +3 Volts +12V DC GND P5BV-C2L/WiFi-AP ATX Power +12V DC +3 Volts GND +12 Volts +12 Volts +5V Standby Power OK Ground +5 Volts Ground +5 Volts Ground +3 Volts +3 Volts Connector · · · · For a fully configured system, we recommend that you use a power supply unit (PSU) that complies with ATX 12 V Specification 2. 0 (or later version) and provides a minimum power of 400 W. Do not forget to connect the 4-pin ATX12V power plug; otherwise, the system will not boot. Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate. The ATX 12 V Specification 2. 0-compliant (400W) PSU has been tested to support the motherboard power requirements. 1-36 R Chapter 1: Product introduction 11. System panel connector (20-8 pin PANEL) This connector supports several chassis-mounted functions. PA NEL P5BV-C2L/WiFi-AP SPEAKER Ground Reset Ground PWR PLED PLEDPLED+ IDE_LEDIDE_LED+ P5BV-C2L/WiFi-AP System Panel Connector * Requires an ATX power supply · System power LED (2-pin PLED) This 2-pin connector is for the system power LED. Connect the chassis power LED cable to this connector. The system power LED lights up when you turn on the system power, and blinks when the system is in sleep mode. A Format 3 1/2 Floppy Disk window appears. D:\bootdisk\makeboot a: e. Press <Enter>, then follow screen instructions to continue. 2. 2-2 assuming that D: is your optical drive. Copy the original or the latest motherboard BIOS file to the bootable floppy disk. Chapter 2: BIOS setup 2. 1. 2 ASUS EZ Flash utility The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is accessible by pressing <Alt> + <F2> during the Power-On Self Tests (POST). Visit the ASUS website (www. asus. com) to download the latest BIOS file for the motherboard and rename the same to P5BMXWAP. ROM. Save the BIOS file to a floppy disk, then restart the system. Press <Alt> + <F2> during POST to display the following. EZFlash starting BIOS update Checking for floppy. . . 4. Insert the floppy disk that contains the BIOS file to the floppy disk drive. When the correct BIOS file is found, EZ Flash performs the BIOS update process and automatically reboots the system when done. EZFlash starting BIOS update Checking for floppy. . . Start erasing. . . . . . . | Start programming. . . | Flashed successfully. Rebooting. · · Do not shut down or reset the system while updating the BIOS to prevent system boot failure!A "Floppy not found!" error message appears if there is no floppy disk in the drive. [. . . ] Visit www. intel. com for more information on the EM64T feature. Visit www. microsoft. com for more information on Windows® 64-bit OS. · · Using the Intel® EM64T feature To use the Intel® EM64T feature: 1. Install a 64-bit operating system (Windows® XP Professional x64 Edition or Windows® Server 2003 x64 Edition). Install an Intel® Pentium® 4 CPU that supports the Intel® EM64T. 3. [. . . ]