User manual ASUS P5VDC-MX

[. . . ] Motherboard P5VDC-MX E2545 Revised Edition V2 March 2006 Copyright © 2006 ASUSTeK COMPUTER INC. All Rights Reserved. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ("ASUS"). Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. ASUS PROVIDES THIS MANUAL "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. [. . . ] Select C r e a t e a n M S - D O S s t a r t u p d i s k from the format options field, then click S t a r t t. Windows® 2000 environment To create a set of boot disks for Windows® 2000: a. Insert a formatted, high density 1. 44 MB floppy disk into the drive. Insert the Windows® 2000 CD to the optical drive. From the Open field, type D:\bootdisk\makeboot a: assuming that D: is your optical drive. 2-2 Chapter 2: BIOS setup e. Press <Enter>, then follow screen instructions to continue. Copy the original or the latest motherboard BIOS file to the bootable floppy disk. 2. 1. 2 ASUS EZ Flash utility The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS-based utility. The EZ Flash utility is built-in the BIOS chip so it is accessible by pressing <Alt> + <F2> during the Power-On Self Tests (POST). To use EZ Flash feature on motherboards with onboard VGA, you will not see the screen display when the BIOS is refreshed. Install a graphics card into the expansion slot to display BIOS update message. To update the BIOS using EZ Flash: 1. Visit the ASUS website (www. asus. com) to download the latest BIOS file for the motherboard and rename the same to P 5 V D C M X . Save the BIOS file to a floppy disk, then restart the system. Press <Alt> + <F2> during POST to display the following. EZFlash starting BIOS update Checking for floppy. . . 4. Insert the floppy disk that contains the BIOS file to the floppy disk drive. When the correct BIOS file is found, EZ Flash performs the BIOS update process and automatically reboots the system when done. EZFlash starting BIOS update Checking for floppy. . . Start erasing. . . . . . . | Start programming. . . | Flashed successfully. Rebooting. · · Do not shutdown or reset the system while updating the BIOS to prevent system boot failure!A "Floppy not found!" error message appears if there is no floppy disk in the drive. A "P5VDCMX. ROM not found!" error message appears if the correct BIOS file is not found in the floppy disk. Make sure that you rename the BIOS file to P5VDCMX. ROM. ASUS P5VDC-MX 2-3 2. 1. 3 AFUDOS utility The AFUDOS utility allows you to update the BIOS file in DOS environment using a bootable floppy disk with the updated BIOS file. This utility also allows you to copy the current BIOS file that you can use as backup when the BIOS fails or gets corrupted during the updating process. Copying the current BIOS To copy the current BIOS file using the AFUDOS utility: · · Make sure that the floppy disk is not write-protected and has at least 600 KB free space to save the file. The succeeding BIOS screens are for reference only. The actual BIOS screen displays may not be exactly the same as shown. 1. 2. Copy the AFUDOS utility (afudos. exe) from the motherboard support CD to the bootable floppy disk you created earlier. Boot the system in DOS mode, then at the prompt type: afudos /o[filename] where the [filename] is any user-assigned filename not more than eight alphanumeric characters for the main filename and three alphanumeric characters for the extension name. A:\>afudos /oOLDBIOS1. ROM Main filename Extension name 3. Press <Enter>. [. . . ] e, The supported RAID configurations appear on a pop-up menu. RAID RAID RAID RAID RAID 0 for performance 1 for data protection 1 for data protection 0/1 SPAN for capacity 2. Select R A I D 1 f o r d a t a p r o t e c t i o n then press <Enter>. 3-10 Chapter 3: Software support 3. 4. From this point, you can auto-configure the RAID array by selecting A u t o S e t u p f o r D a t a S e c u r i t y or manually configure the RAID array for mirrored sets. If you want to auto-configure, proceed to the next step, otherwise, skip to step 6. Select A u t o S e t u p f o r D a t a S e c u r i t y and press <Enter>. The following confirmation message appears. Auto create array will destroy all data on disks, Continue? [. . . ]