User manual ASUS P8B75-M LE

[. . . ] It can be switched between AGP 2X(3. 3V) or 4X (1. 5V) mode by adjusting the jumper. The factory default for this card is 2X(3. 3V). The GA-8VT800 motherboards might not function properly, if you install this card without switching the jumper to 4X(1. 5V) mode in it. Example 2: Some ATi Rage 128 Pro graphics cards made by "Power Color", the graphics card manufacturer & some SiS 305 cards, their golden finger is compatible with 2X/4X mode AGP slot, but they support 2X(3. 3V) only. The GA-8VT800 motherboards might not function properly, If you install this card in it. [. . . ] (Default Value) Enable onboard LPT port and address is 278/IRQ5. Enable onboard LPT port and address is 3BC/IRQ7. Parallel Port Mode SPP EPP ECP ECP+EPP Using Parallel port as Standard Parallel Port. (Default Value) Using Parallel port as Enhanced Parallel Port. Using Parallel port as Extended Capabilities Port. Using Parallel port as ECP & EPP mode. Game Port Address 201 209 Disabled Set Game Port Address to 201. (Default Value) Set Game Port Address to 209. Disable this function. Midi Port Address 300 330 Disabled Set Midi Port Address to 300. Set Midi Port Address to 330. (Default Value) Disable this function. Midi Port IRQ 5 10 Set Midi Port IRQ to 5. (Default Value) GA-8VT800(-L) Motherboard - 42 - English Power Management Setup CMOS Setup Utility-Copyright (C) 1984-2003 Award Software ACPI Suspend Type x USB Device Wake-Up From S3 Soft-Off by PWRBTN AC BACK Function Keyboard Power On Mouse Power On PME Event Wake Up Modem Ring Resume Resume by Alarm x Date (of Month) Alarm x Time (hh:mm:ss) Power Management Setup [S1(POS)] [Disabled] [Instant-Off] [Soft-Off] [Disabled] [Disabled] [Enabled] [Enabled] [Disabled] Ev eryday 000 Item Help Menu Level u [S1] Set suspend type to Power On Suspend under ACPI OS [S3] PSet suspend type to Suspend to RAM under ACPI OS higf: Move Enter:Select +/-/PU/PD:Value F10:Save ESC:Exit F5:Previous Values F6:Fail-Safe Defaults F1:General Help F7:Optimized Defaults Figure 5: Power Management Setup ACPI Suspend Type S1(POS) S3(STR) Set ACPI suspend type to S1. (Default Value) Set ACPI suspend type to S3. USB Device Wake-Up from S3 Disabled Enabled Disabled USB Device Wake-Up from S3. (Default Value) Enabled USB Device Wake-Up from S3. Soft-Off by PWRBTN Instant-off Delay 4 Sec. (Default value) Supports adjustable CPU Vcore from 0. 8375V to 1. 600V by 0. 025V step. Incorrect using it may cause your system to fail. For power End-User use only! Normal CPU Vcore Display your CPU Vcore Voltage. AGP OverVoltage Control Auto +0. 1V +0. 2V Supply voltage as AGP Card reguired. (Default value) Set AGP OverVoltage Control to +0. 1V. Set AGP OverVoltage Control to +0. 2V. Increase AGP voltage may get stable for Over_Clock. But it may damage to AGP Card when enable this feature. DIMM OverVoltage Control Auto +0. 1V +0. 2V Supply voltage as DRAM module reguired. (Default value) Set DIMM OverVoltage Control to +0. 1V. Set DIMM OverVoltage Control to +0. 2V. Increase DRAM voltage may get stable for Over_Clock. But it may damage to DRAM module when enable this feature. - 49 - BIOS Setup English Load Fail-Safe Defaults CMOS Setup Utility-Copyright (C) 1984-2003 Award Software }Standard CMOS Features }Advanced BIOS Features }Integrated Peripherals }Power Management Setup }PnP/PCI Configurations }PC Health Status Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Load Fail-Safe Defaults?(Y/N)?Y Saving Exit Without higf:Select Item F10:Save & Exit Setup Load Fail-Safe Defaults Figure 9: Load Fail-Safe Defaults }Frequency/Voltage Control ESC:Quit F8: Q-Flash Load Fail-Safe Defaults Fail-Safe defaults contain the most appropriate values of the system parameters that allow minimum system performance. GA-8VT800(-L) Motherboard - 50 - English Load Optimized Defaults CMOS Setup Utility-Copyright (C) 1984-2003 Award Software }Standard CMOS Features }Advanced BIOS Features }Integrated Peripherals }Power Management Setup }PnP/PCI Configurations }PC Health Status Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Load Optimized Defaults?(Y/N)?YSaving higf:Select Item F10:Save & Exit Setup Load Optimized Defaults Figure 10: Load Optimized Defaults }Frequency/Voltage Control ESC:Quit F8: Q-Flash Load Optimized Defaults Selecting this field loads the factory defaults for BIOS and Chipset Features which the system automatically detects. - 51 - BIOS Setup English Set Supervisor/User Password CMOS Setup Utility-Copyright (C) 1984-2003 Award Software }Standard CMOS Features }Advanced BIOS Features }Integrated Peripherals }Power Management Setup }PnP/PCI Configurations }PC Health Status Load Fail-Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save & Exit Setup Exit Without Saving Enter Password: }Frequency/Voltage Control ESC:Quit F8: Q-Flash higf:Select Item F10:Save & Exit Setup Change/Set/Disable Password Figure 11: Password Setting When you select this function, the following message will appear at the center of the screen to assist you in creating a password. [. . . ] No Plug the CPU cooling fan power in the CPU fan connector. Plug in the AC power connector. Check if the CPU cooling fan attached to CPU properly. ls CPU cooling fan power connected to CPU_FAN properly?No Insert and push the memory module vertically into the DIMM slot. Check if the memory install properly into the DIMM slot. [. . . ]