User manual ASUS TS100-E5/PI4

[. . . ] TS100-E5/PI4 Intel® Xeon 3300/3200/3100/3000 Series LGA775 Pedestal Server E3763 First Edition April 2008 Copyright © 2008 ASUSTeK COMPUTER INC. No part of this manual, including the products and software described in it, may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purposes, without the express written permission of ASUSTeK COMPUTER INC. ASUS provides this manual "as is" without warranty of any kind, either express or implied, including but not limited to the implied warranties or conditions of merchantability or fitness for a particular purpose. In no event shall ASUS, its directors, officers, employees, or agents be liable for any indirect, special, incidental, or consequential damages (including damages for loss of profits, loss of business, loss of use or data, interruption of business and the like), even if ASUS has been advised of the possibility of such damages arising from any defect or error in this manual or product. [. . . ] NorthBridgeConfiguration SouthBridgeConfiguration BIOS SETUP UTILITY ConfigureNorthBridge features. NorthBridgeConfiguration Advanced BIOS SETUP UTILITY ENABLE: Allow remapping of overlapped PCI memory above the total physical memory. DISABLE: Do no allow remapping of memory. NorthBridgechipsetConfiguration MemoryRemapFeature [Enabled] PCIMMIOAllocation:4GBTo3584MB DRAMFrequency [Auto] ConfigureDRAMTimingbySPD [Enabled] InitiateGraphicAdapter PEGPortConfiguration PEGPort [PEG/PCI] [Auto] Memory Remap Feature [Enabled] Allows you to enable or disable the remapping of the overlapped PCI memory above the total physical memory. Enable this option only when you install 64-bit operating system. Configuration options: [Disabled] [Enabled] Disable this item if you are using RedHat Linux Advanced Server 3. 0 UP5/UP6 operating system. DRAM Frequency [Auto] Allows you to set the DDR operating frequency. Configuration options: [Auto] [667 MHz] [800 MHz] ConfigureDRAMTimingbySPD[Enabled] When this item is enabled, the DRAM timing parameters are set according to the DRAM SPD (Serial Presence Detect). When disabled, you can manually set the DRAM timing parameters through the DRAM sub-items. Configuration options: [Enabled] [Disabled] DRAM CAS# Latency [5] Controls the latency between the SDRAM read command and the time the data actually becomes available. Configuration options: [3] [4] [5] [6] 4-20 Chapter 4: BIOS setup DRAM RAS# to CAS# Delay [6 DRAM Clocks] Controls the latency between the DDR SDRAM active command and the read/write command. Configuration options: [3 DRAM Clocks] [4 DRAM Clocks] [5 DRAM Clocks] [6 DRAM Clocks] DRAM RAS# Precharge [6 DRAM Clocks] Controls the idle clocks after issuing a precharge command to the DDR SDRAM. Configuration options: [3 DRAM Clocks] [4 DRAM Clocks] [5 DRAM Clocks] [6 DRAM Clocks] DRAM RAS# Activate to Precharge Delay [15 DRAM Clocks] Configuration options: [9 DRAM Clocks] [10 DRAM Clocks] ~ [15 DRAM Clocks] Initiate Graphic Adapter [PEG/PCI] Allows you to select the graphics controller as the primary boot device. Configuration options: [PCI/PEG] [PEG/PCI] PEGPortConfiguration PEG Port [Auto] Configuration options: [Auto] [Disabled] SouthBridgeConfiguration Advanced SMBUSController BIOS SETUP UTILITY Options Enabled Disabled SouthBridgechipsetConfiguration [Enabled] SLP_S4#Min. AssertionWidth[1to2seconds] SMBUS Controller [Enabled] Allows you to enable or disable the SMBUS Controller. Configuration options: [Enabled] [Disabled] SLP_S4# Min. Assertion Width [1 to 2 seconds] Allows you to select the SLP_S4# Min. Configuration options: [4 to 5 seconds] [3 to 4 seconds] [2 to 3 seconds] [1 to 2 seconds] ASUS TS100-E5/PI4 4-21 4. 4. 7 OnboardDevicesConfiguration The Onboard Devices Configuration menu allows you to change the onboard devices settings. Select an item then press <Enter> to display the sub-menu. Advanced SerialPort1Address SerialPort2Address PCIELAN-8056A LAN8056ABootROM PCIELAN-8056B LAN8056BBootROM PCIELAN-8056C LAN8056CBootROM PCIELAN-8056D LAN8056DBootROM PCIEMarvell6145 BIOS SETUP UTILITY Allows BIOS to Select Serial Port1 Base Addresses. ConfigureWin83627DHG-ASuperIOChipset [3F8/IRQ4] [2F8/IRQ3] [Enabled] [Disabled] [Enabled] [Disabled] [Enabled] [Disabled] [Enabled] [Disabled] [Enabled] v02. 58(C)Copyright1985-2007, AmericanMegatrends, Inc. Serial Port1 Address [3F8/IRQ4] Allows you to select the Serial Port1 base address. Configuration options: [Disabled] [3F8/IRQ4] [3E8/IRQ4] Serial Port2 Address [2F8/IRQ3] Allows you to select the Serial Port2 base address. Configuration options: [Disabled] [2F8/IRQ3] [2E8/IRQ3] PCIE LAN-8056A / B / C / D [Enabled] Allows you to hide or active PCIE LAN-8056A, B, C, or D. Configuration options: [Disabled] [Enabled] LAN8056A / B / C / D Boot ROM [Disabled] Allows you to enable or disalbe the Boot ROM of LAN8056A, B, C or D. Configuration options: [Disabled] [Enabled] PCIE Marvell 6145 [Enabled] Allows you to enable or disable the Marvell 6145 SATA controller. Configuration options: [Disabled] [Enabled] 4-22 Chapter 4: BIOS setup 4. 4. 8 PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. [. . . ] You can download the latest BIOS file from the ASUS website (www. asus. com/ support/download/) if you need to update the BIOS. Visit www. intel. com for more information on the EIST feature. · A. 2. 1 · · · System requirements Before using EIST, check your system if it meets the following requirements: Intel® Pentium® 4 processor with EIST support BIOS file with EIST support Operating system with EIST support (Windows® XP SP2/Linux 2. 6 kernel or later versions) A-2 Appendix: Reference information A. 2. 2 1. 7. Using the EIST To use the EIST feature: Turn on the computer, then enter the BIOS Setup. Go to the Advanced Menu, highlight CPUConfiguration, then press <Enter>. [. . . ]