User manual ASUS TS300-E4/PX4

[. . . ] Specifications and information contained in this manual ae furnished for informational use only, and are subject to change at any time without notice, and should not be construed as a commitment by ASUS. ASUS assumes no responsibility or liability for any errors or inaccuracies that may appear in this manual, including the products and software described in it. Product warranty or service will not be extended if: (1) the product is repaired, modified or altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the serial number of the product is defaced or missing. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Configuration options: [Disabled] [Enabled] 5-16 Chapter 5: BIOS setup 5. 4. 2 RemoteAccessConfiguration The items in this menu allows you to configure the Remote Access features. Select an item then press <Enter> to display the configuration options. Advanced RemoteAccess BIOS SETUP UTILITY Select Remote Access type. ConfigureRemoteAccesstypeandparameters [Enabled] Serialportnumber [COM1] BaseAddress, IRQ [3F8h, 4] SerialPortMode [1152008, n, 1] FlowControl [None] RedirectionAfterBIOSPOST [Always] TerminalType [ANSI] VT-UTF8ComboKeySupport[Enabled] Select Screen Select Item +- Change Option F1 General Help F10 aveandExit S ESC xit E v02. 58(C)Copyright1985-2007, AmericanMegatrends, Inc. Remote Access [Disabled] Enables or disables the remote access feature. Configuration options: [Disabled] [Enabled] The following items appear only when the Remote Access item is set to [Enabled]. Serial port number [COM1] Allows you to select a serial port for console redirection. Configuration options: [COM1] [COM2] Serial Port Mode [115200 8, n, 1] Allows you to select a serial port mode. Configuration options: [115200 8, n, 1] [57600 8, n, 1] [38400 8, n, 1] [19200 8, n, 1] [09600 8, n, 1] Flow Control [None] Allows you to set the flow control for console redirection. Configuration options: [None] [Hardware] [Software] Redirection After BIOS POST [Always] Sets the redirection mode after the BIOS Power-On Self-Test (POST). Some operating systems may not work when this item is set to Always. Configuration options: [Disabled] [Boot Loader] [Always] ASUS TS300-E5 5-17 Terminal Type [ANSI] Allows you to select the target terminal type. Configuration options: [ANSI] [VT100] [VT-UTF8] VT-UTF8 Combo Key Support [Enabled] Allows you to enable or disable VT-UTF8 Combination Key Support for ANSI/ VT100 terminals. Configuration options: [Disabled] [Enabled] 5. 4. 3 Trusted Computing Advanced BIOS SETUP UTILITY Enable/Disable TPM TCG (TPM 1. 1/1. 2) supp in BIOS Trusted Computing TCG/TPMSUPPORT [No] Select Screen Select Item +- Change Option F1 General Help F10 aveandExit S ESC xit E v02. 58(C)Copyright1985-2007, AmericanMegatrends, Inc. TCG/TPM SUPPORT [No] Allows you to set the TCG/TPM SUPPORT. Configuration options: [PCI/PEG] [PEG/PCI] PEGPortConfiguration PEG Port [Auto] Configuration options: [Auto] [Disabled] SouthBridgeConfiguration Advanced BIOS SETUP UTILITY SouthBridgechipsetConfiguration SMBUSController [Enabled] SLP_S4#Min. AssertionWidth[1to2seconds] SMBUS Controller [Enabled] Allows you to enable or disable the SMBUS Controller. Configuration options: [Enabled] [Disabled] SLP_S4# Min. Assertion Width [1 to 2 seconds] Allows you to select the SLP_S4# Min. Configuration options: [4 to 5 seconds] [3 to 4 seconds] [2 to 3 seconds] [1 to 2 seconds] ASUS TS300-E5 5-21 5. 4. 7 OnboardDevicesConfiguration The Onboard Devices Configuration menu allows you to change the onboard devices settings. Select an item then press <Enter> to display the sub-menu. Advanced SerialPort1Address SerialPort2Address SerialPort2Mode PCIELAN-5721A LAN5721ABootROM PCIELAN-5721B LAN5721BBootROM PCIELAN-5721C LAN5721CBootROM PCIELAN-5721D LAN5721DBootROM BIOS SETUP UTILITY Allows BIOS to Select Serial Port1 Base Addresses. ConfigureWin83627EHG-ASuperIOChipset [3F8/IRQ4] [2F8/IRQ3] [Normal] [Enabled] [Disabled] [Enabled] [Disabled] [Enabled] [Disabled] [Enabled] [Disabled] v02. 58(C)Copyright1985-2007, AmericanMegatrends, Inc. Serial Port1 Address [3F8/IRQ4] Allows you to select the Serial Port1 base address. Configuration options: [Disabled] [3F8/IRQ4] [3E8/IRQ4] Serial Port2 Address [2F8/IRQ3] Allows you to select the Serial Port2 base address. Configuration options: [Disabled] [2F8/IRQ3] [2E8/IRQ3] PCIE LAN-5721A / B / C / D [Enabled] Allows you to hide or active PCIE LAN-5721A, B, C, or D. Configuration options: [Disabled] [Enabled] LAN5721A / B / C / D Boot ROM [Disabled] Allows you to Configure LAN5721A, LAN5721B, LAN5721C or LAN5721D Boot ROM. Configuration options: [Disabled] [Enabled] 5-22 Chapter 5: BIOS setup 5. 4. 8 PCI PnP The PCI PnP menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices. Take caution when changing the settings of the PCI PnP menu items. [. . . ] Enter # cd/usr/src/linux # cat/patch-location/sk98lin_vX. XX_a_b_c_patch | patch -p1. Enter makemenuconfig, select Broadcom 1000 Lan from the prompt menu, and then select M from the submenu. Enter make modules SUBDIRS=drivers/net/sk98lin/ V=1. Enter make modules_install SUBDIRS=drivers/net/sk98lin/ V=1. [. . . ]