User manual ASUS V3-P5G45

[. . . ] Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. The product name and revision number are both printed on the product itself. Manual revisions are released for each product design represented by the digit before and after the period of the manual revision number. Manual updates are represented by the third digit in the manual revision number. [. . . ] 32 Connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 5 System Package Contents The following checklist enumerates the components included in the standard system package. 1) 2) 3) 4) 5) 6) 7) 8) System Chassis Motherboard Switching Power Supply 1. 44MB Floppy Disk Drive CD-ROM Drive (optional) 56K PCI Modem Card (optional) Support CD with Drivers and Utilities Installation Guide NOTE If you are assembling the system by yourself, make sure to prepare all the components before starting. It saves you a lot of time not having to hunt down components when you need them. 6 Introduction "About This Guide" contains an introduction on the contents of this document that include target audience and chapter description. ASUS Terminator Barebone System About This Guide 7 You are reading the ASUS Terminator Barebone System Installation Guide. This guide provides general information and installation instructions about the Terminator Barebone System. Audience This installation guide is intended for experienced users and integrators with hardware knowledge of personal computers. Checklist Contents Description This installation guide contains the following parts: 1. Introduction: About This Guide This part contains an introduction on the contents of this document that include target audience and chapter description. Chapter 1: System Introduction This chapter gives a general description of the ASUS Terminator barebone system. It includes introduction on the front and rear panel features, and the internal features. Chapter 2: Basic Installation This chapter tells how to install components into the barebone system through illustrated step-by-step instructions. Chapter 3: Motherboard Information This chapter gives information about the CUSC motherboard that comes with the ASUS Terminator Barebone System. This chapter includes the motherboard layout, jumper settings, and connector locations. It also includes information on the USB/audio board located on the front panel. 8 Introduction: About This Guide Chapter 1 This chapter gives a general description of the ASUS Terminator barebone system. Position the CPU above the socket such that its notched or marked corner matches the Socket Pin 1, while making sure that the CPU is parallel to the socket. Notched Corner Socket Pin 1 4. Carefully insert the CPU into the socket until it fits in place. 5. The lever clicks in place indicating that the socket is locked. Connect the CPU fan cable to the 3-pin CPU_FAN connector on the motherboard. Refer to the picture in step 1. CPU Fan Cable WARNING!Connect the other end of the IDE ribbon cable to the primary IDE connector (blue connector labeled IDE1) on the motherboard. Primary IDE Connector (IDE1) 20 Chapter 2: Basic Installation 2. 6 Install a CD-ROM Drive A CD-ROM drive is an optional item in the Terminator barebone system. Refer to the instructions in this section if you acquired a model without a CD-ROM. Follow these steps to install a CD-ROM drive. Insert the CD-ROM drive into the upper 5. 25-inch bay. 5. 25-inch Drive Bay 3. Carefully push the CD-ROM drive into the bay until its screw holes align with the holes on the bay as shown. Secure the CD-ROM with two screws on each side of the bay. CD-ROM Screws ASUS Terminator Barebone System 21 2. 6 Install a CD-ROM Drive 5. [. . . ] Connect the power switch and power LED cables to their respective leads in the PANEL connector on the motherboard. Connect the HDD LED cable to the 2-pin lead marked IDELED. Connect the Line Out/Mic cable to the FLOUT/MIC2 connector on the motherboard, matching the red pin stripe with Pin 1. Connect the USB2P cable to the USB1 connector on the motherboard, matching the red pin stripe with Pin 1. USB1 Connector Speaker Connector Speaker Ground Ground +5V Ground Reset Ground PWR Ground ExtSMI# TB_LED +5 V Reset SW ATX Power Switch* SMI Lead Message LED Power LED PLED +5 V PANEL Connector IDELED Lead * Requires an ATX power supply. Pin 1 FLOUT Lead (for Line Out Cable) MIC2 Lead (for Microphone Cable) ASUS Terminator Barebone System 25 2. 10 Replace the Cover After you have installed all the internal components and you have connected all the necessary cables, you are now ready to put the system back together. [. . . ]