User manual ASUS VE228T

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Table of contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] All eight hooks (four hooks on both sides) of the cover must properly fit the designated holes. 3. Slide the cover to the direction of the front panel until it fits in place. 4. Replace the cover screws. ASUS Pundit-PE3 2-21 2. 10 Installing the foot stands You need to install the foot stands to place the system vertically on your desktop. Lay the system on its side on a flat, stable, and elevated surface, then locate two screw holes on the left side of the system. Extend the left side of the system at least 3 cm from the edge of surface to facilitate installation. Position the foot stand on the chassis side until their screw holes align. 2. 3. 4. 5. Drive in a screw to secure the footstand to the chassis. Repeat steps 3 to 4 to install the the second foot stand. The photo on the right shows the system in a vertical desktop placement. 2-22 Chapter 2: Basic installation 2. 11 Selecting the voltage The system's power supply unit has a 115 V/230 V voltage selector switch located beside the power connector. Use this switch to select the appropriate system input voltage according to the voltage supply in your area. If the voltage supply in your area is 100-127 V, set the switch to 115 V. If the voltage supply in your area is 200-240 V, set the switch to 230 V. Setting the switch to 115 V in a 230 V environment will seriously damage the system! 2. 12 Connecting external devices To the front panel Camera Headphone or Audio Device Scanner Mic ASUS Pundit-PE3 2-23 To the rear panel Po w e r o u t l e t Line Out Mic Recorder Card reader Hub or router VGA monitor Camera Serial mouse Printer S/2 P S/2 Mouse P S / 2 K B 2-24 Chapter 2: Basic installation Chapter 3 This chapter helps you power up the system and install drivers and utilities from the support CD. ASUS Pundit-PE3 Getting started 3. 1 Installing an operating system This system supports Windows® 2000/XP operating systems (OS). Always install the latest OS version and corresponding updates to maximize the features of your system. · Motherboard settings and hardware options vary. Use the setup procedures presented in this chapter for reference only. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the cap on pins 2-3 for about 5~10 seconds, then move the cap back to pins 1-2. Plug the power cord and turn ON the computer. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data. Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure! 4. 6. ® CLRTC1 12 Normal (Default) 23 Clear CMOS Clear RTC RAM ASUS Pundit-PE3 4-3 2. USB device wake-up (3-pin USBPW12, USBPW34, USBPW56, USBPW78) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). USBPW12 USBPW34 2 1 +5V (Default) ® 3 2 +5VSB USBPW56 USBPW78 12 23 USB device wake-up · +5V (Default) +5VSB The USB device wake-up feature requires a power supply that can provide 500mA on the +5VSB lead for each USB port; otherwise, the system will not power up. The total current consumed must NOT exceed the power supply capability (+5VSB) whether under normal condition or in sleep mode. · 3. Keyboard power (3-pin KBPWR1) This jumper allows you to enable or disable the keyboard wake-up feature. Set this jumper to pins 1-2 (+5V) if you do not want to wake up the computer when you press a key on the keyboard. This feature requires an ATX power supply that can supply at least 1A on the +5VSB lead, and a corresponding setting in the BIOS. KBPWR1 12 +5V 23 +5VSB (Default) ® Keyboard power setting 4-4 Chapter 4: Motherboard info 4. 3 4. 3. 1 4. 3. 2 1. Connectors Rear panel connectors Internal connectors Refer to section "1. 3 Rear panel" for a description of the rear panel I/O ports. Primary IDE connector (40-1 pin PRI_IDE1) This connector is for an Ultra DMA 100/66/33 signal cable. The Ultra DMA 100/66/33 signal cable has three connectors: a blue connector for the primary IDE connector on the motherboard, a black connector for an Ultra DMA 100/66/33 IDE slave device (optical drive/hard disk drive), and a gray connector for an Ultra DMA 100/66/33 IDE master device (hard disk drive). [. . . ] From the password box, type a password composed of at least six letters and/or numbers, then press <Enter>. Confirm the password when prompted. The message "Password Installed" appears after you successfully set your password. To change the supervisor password, follow the same steps as in setting a user password. To clear the supervisor password, select the Change Supervisor Password then press <Enter>. [. . . ]