User manual ASUS VH242TL

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Plug the power cord and turn ON the computer. Hold down the <Del> key during the boot process and enter BIOS setup to re-enter data. Except when clearing the RTC RAM, never remove the cap on CLRTC jumper default position. Removing the cap will cause system boot failure! P5L-MX/IPAT CLRTC 12 Normal (Default) 23 Clear CMOS R P5L-MX/IPAT Clear RTC RAM You do not need to clear the RTC when the system hangs due to overclocking. For system failure due to overclocking, use the C. P. R. Shut down and reboot the system so the BIOS can automatically reset parameter settings to default values. 1-22 Chapter 1: Product introduction 2. USB device wake-up (3-pin USBPW1234, USBPW5678) Set these jumpers to +5V to wake up the computer from S1 sleep mode (CPU stopped, DRAM refreshed, system running in low power mode) using the connected USB devices. Set to +5VSB to wake up from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh, power supply in reduced power mode). The USBPW1234 jumper is for the rear USB ports. The USBPW5678 jumper is for the internal USB connectors that you can connect to additional USB ports. USBPW1234 12 23 P5L-MX/IPAT +5V (Default) +5VSB USBPW5678 12 R 23 P5L-MX/IPAT USB Device Wake Up (Default) · +5V +5VSB The USB device wake-up feature requires a power supply that can provide 500 mA on the +5VSB lead for each USB port; otherwise, the system would not power up. The total current consumed must NOT exceed the power supply capability (+5VSB) whether under normal condition or in sleep mode. · ASUS P5L-MX/IPAT 1-23 1. 10 Connectors 1. 10. 1 Rear panel connectors 1 2 3 4 5 6 11 1. 3. 10 9 8 7 PS/2 mouse port (green). This 25-pin port connects a parallel printer, a scanner, or other devices. DO NOT place jumper caps on the fan connectors. CPU FAN PWM CPU FAN IN CPU FAN PWR GND CPU_FAN CHA_FAN P5L-MX/IPAT GND +12V Rotation R P5L-MX/IPAT Fan Connectors 5. Digital Audio connector (4-1 pin SPDIF_OUT) This connector is for the S/PDIF audio module to allow digital sound output. Connect one end of the S/PDIF audio cable to this connector and the other end to the S/PDIF module. P5L-MX/IPAT R P5L-MX/IPAT CPU Digital Audio Connector SPDIF_OUT The S/PDIF out module is purchased separately. 1-28 +5V Chapter 1: Product introduction SPDIFOUT GND 6. ATX power connectors (24-pin EATXPWR and 4-pin ATX12V) These connectors are for ATX power supply plugs. The power supply plugs are designed to fit these connectors in only one orientation. Find the proper orientation and push down firmly until the connectors completely fit. · · Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot. Use of a PSU with a higher power output is recommended when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate. Make sure that your power supply unit (PSU) can provide at least the minimum power required by your system. See the table below for details. · EATX12V +12V DC GND EATXPWR Ground +5 Volts +5 Volts +5 Volts -5 Volts Ground Ground Ground PSON# Ground -12 Volts +3 Volts R P5L-MX/IPAT ATX Power +12V DC +3 Volts GND +12 Volts +12 Volts +5V Standby Power OK Ground +5 Volts Ground +5 Volts Ground +3 Volts +3 Volts Connector ASUS P5L-MX/IPAT P5L-MX/IPAT 1-29 7. Optical drive audio connector (4-pin CD) This connector is for the 4-pin audio cable that connects to the audio connector at the back of the optical drive. R CD (black) P5L-MX/IPAT Internal Audio Connector Enable the CD-IN function in the audio utility when using this connector. 8. USB connectors (10-1 pin USB56, USB78) These connectors are for USB 2. 0 ports. Connect the optional USB module cable to any of these connectors, then install the module to a slot opening at the back of the system chassis. These USB connectors comply with USB 2. 0 specification that supports up to 480 Mbps connection speed. USB+5V USB_P6USB_P6+ GND NC Right Audio Channel Ground Ground Left Audio Channel P5L-MX/IPAT P5L-MX/IPAT USB56 USB78 1 USB+5V USB_P5USB_P5+ GND 1 USB+5V USB_P7USB_P7+ GND R P5L-MX/IPAT USB 2. 0 Connectors Never connect a 1394 cable to the USB connectors. Doing so will damage the motherboard! 1-30 Chapter 1: Product introduction USB+5V USB_P8USB_P8+ GND NC 9. Front panel audio connector (10-1 pin AAFP) This connector is for a chassis-mounted front panel audio I/O module that supports either HD Audio or legacy AC'97 audio standard. Azalia-compliant pindefinition MIC2_JD PRESENSE# AGND Legacy AC'97-compliant pindefinition HP_HD P5L-MX/IPAT NC NC AGND NC AAFP Line out_L NC Line out_R MIC2_R MIC2_L HP_L Jack_Sense HP_R MIC2_R MIC2_L R P5L-MX/IPAT Front Panel Audio Connector It is recommended that you connect a high-definition front panel audio module to this connector to avail of the motherboard's high-definition audio capability. ASUS P5L-MX/IPAT 1-31 10. [. . . ] Install an Intel® Pentium® 4 CPU that supports the Intel® EM64T. Install a 64-bit operating system (Windows® XP Professional x64 Edition or Windows® Server 2003 x64 Edition). Install the 64-bit drivers for the motherboard components and devices from the support CD. Install the 64-bit drivers for expansion cards or add-on devices, if any. Refer to the expansion card or add-on device(s) documentation, or visit the related website, to verify if the card/device supports a 64-bit system. A. 2 Enhanced Intel SpeedStep® Technology (EIST) · The motherboard comes with a BIOS file that supports EIST. [. . . ]