User manual ASUS VK193S

[. . . ] IN NO EVENT SHALL ASUS, ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR ERROR IN THIS MANUAL OR PRODUCT. SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. ii Contents Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The system may become unstable or may not boot up if the power is inadequate. Do not forget to connect the 4-pin ATX +12 V power plug; otherwise, the system will not boot up. We recommend that you use a PSU with higher power output when configuring a system with more power-consuming devices. The system may become unstable or may not boot up if the power is inadequate. The ATX 12 V Specification 2. 0-compliant PSU passed the motherboard power requirement test with the following configuration: CPU : Memory : Graphics card : Parallel ATA devices: Serial ATA device : Optical drives : SCSI devices : Intel® Pentium® 4 3. 6 GHz 512 MB DDR (x 4) PCI Express x16 Nvidia EN5900 IDE hard disk drive (x 2) SATA hard disk drive CD-ROM (x 2) SCSI card and SCSI hard disk drive ATX12V1 GND +12V DC · · · · EATXPWR +3 Volts +12 Volts +12 Volts +5V Standby Power OK Ground +5 Volts Ground +5 Volts Ground +3 Volts +3 Volts Ground +5 Volts +5 Volts +5 Volts -5 Volts Ground Ground Ground PSON# Ground -12 Volts +3 Volts GND +12V DC P5GDC P5GDC ATX power connectors ASUS P5GDC 1-33 8. Optical drive audio connector (4-pin CD) This connector is for the 4-pin audio cable that connects to the audio connector at the back of the optical drive. P5GDC P5GDC CD audio connector 9. GAME/MIDI port connector (16-1 pin GAME1) This connector is for a GAME/MIDI port. Connect the USB/GAME module cable to this connector, then install the module to a slot opening at the back of the system chassis. The GAME/MIDI port connects a joystick or game pad for playing games, and MIDI devices for playing or editing audio files. P5GDC Right Audio Channel Ground Ground Left Audio Channel CD GAME1 +5V J1B1 J1CX GND GND J1CY J1B2 +5V P5GDC GAME connector 1-34 Chapter 1: Hardware information +5V J2B1 J2CX MIDI_OUT J2CY J2B2 MIDI_IN 1 0 . Chassis intrusion connector (4-1 pin CHASSIS1) This connector is for a chassis-mounted intrusion detection sensor or switch. Connect one end of the chassis intrusion sensor or switch cable to this connector. The chassis intrusion sensor or switch sends a high-level signal to this connector when a chassis component is removed or replaced. The signal is then generated as a chassis intrusion event. Select C r e a t e a n M S - D O S s t a r t u p d i s k from the format options field, then click S t a r t t. Windows® 2000 environment To create a set of boot disks for Windows® 2000: a. Insert a formatted, high density 1. 44 MB floppy disk into the drive. Insert the Windows® 2000 CD to the optical drive. Click S t a r t then select R u n t, n. 2-2 Chapter 2: BIOS setup d. From the Open field, type D:\bootdisk\makeboot a: assuming that D: is your optical drive. Press <Enter>, then follow screen instructions to continue. Copy the original or the latest motherboard BIOS file to the bootable floppy disk. 2. 1. 2 ASUS EZ Flash utility The ASUS EZ Flash feature allows you to update the BIOS without having to go through the long process of booting from a floppy disk and using a DOS-based utility. The EZ Flash utility is built into the BIOS chip so it is accessible by pressing <Alt> + <F2> during the Power-On Self Tests (POST). Visit the system builder's website to download the latest BIOS file for the motherboard and rename the same to P 5 G D C S I . Save the BIOS file to a floppy disk, then restart the system. [. . . ] To clear the supervisor password, select the Change Supervisor Password then press <Enter>. The message "Password Uninstalled" appears. 2-34 Chapter 2: BIOS setup If you forget your BIOS password, you can clear clear it by erasing the CMOS Real Time Clock (RTC) RAM. See section "1. 6 Jumpers" for information on how to erase the RTC RAM. After you have set a supervisor password, the other items appear to allow you to change other security settings. Security Settings Supervisor Password User Password : Not Installed : Not Installed [Full Access] [Setup] [Disabled] <Enter> to change password. <Enter> again to disabled password. Change Supervisor Password User Access Level Change User Password Clear User Password Password Check Boot Sector Virus Protection User Access Level (Full Access] This item allows you to select the access restriction to the Setup items. [. . . ]