User manual ASUS VS229NR

[. . . ] Products and corporate names appearing in this manual may or may not be registered trademarks or copyrights of their respective companies, and are used only for identification or explanation and to the owners' benefit, without intent to infringe. The product name and revision number are both printed on the product itself. Manual revisions are released for each product design represented by the digit before and after the period of the manual revision number. Manual updates are represented by the third digit in the manual revision number. [. . . ] Contact an authorized dealer. · · · CAUTION This product is equipped with a three-wire power cable and plug for the user's safety. Use the power cable with a properly grounded electrical outlet to avoid electrical shock. Operation Safety IMPORTANT · · · Any mechanical operation on this server must be conducted by certified or experienced engineers. Before operating the server, carefully read all the manuals included with the server package. Before using the server, make sure all cables are correctly connected and the power cables are not damaged. If any damage is detected, contact your dealer as soon as possible. To avoid short circuits, keep paper clips, screws, and staples away from connectors, slots, sockets and circuitry. Avoid dust, humidity, and temperature extremes. Place the server on a stable surface. · · 8 Introduction "About This Manual" introduces the contents of this document. This part includes the target audience, chapter description, and conventions used. It also lists other sources of information that are not contained in this manual. AVS229NR Server User's Manual About This Manual 9 Audience This installation guide is intended for system integrators, and experienced users with at least basic knowledge of configuring an entry-level server. Contents This manual contains the following parts: 1. Introduction: About This Manual This part introduces the contents of this document. If your server includes a RAID kit, it comes already pre-installed in the chassis. AVS229NR Server User's Manual 17 18 Chapter 1: System Overview Chapter 2 AVS229NR Server User's Manual Hardware Setup 19 This chapter describes the hardware setup procedures that you have to perform when installing system components. 2. 1 Remove the Front Cover Follow these steps to remove the front panel. Unlock the Front Panel Insert the system key to the keylock and turn it 90 degrees counter clockwise to unlock the front panel cover. Chassis Keylock Remove the Screws Use a Phillips screwdriver to remove the two screws that secure the front panel to the main chassis. Front Panel Screws Remove the Panel 1. Place your hands on the upper part of the panel and pull it firmly. 20 Chapter 2: Hardware Setup 2. 2 Remove the Chassis Cover Follow these steps to remove the chassis cover. Remove the Screws Remove the screws that secure the cover to the main chassis. The locations of the screws are indicated by circles. Remove the Cover Slide the cover for about an inch toward the front and lift it out of the chassis. AVS229NR Server User's Manual 21 2. 3 Motherboard Placement NOTE The motherboard and other internal components of the AVS229NR server are already installed as indicated in section "1. 4 Internal Features". Refer to the motherboard user's manual for detailed technical information about the motherboard. When removing the motherboard, you need to remove the hot-swap trays and the CD-ROM drive first, because they overlap with the motherboard. Refer to Chapter 4 for the procedure to remove the drives. Placement Direction When installing the motherboard, make sure that you place it into the chassis correctly. The edge with the external ports goes to the rear part of the chassis. Rear Panel Motherboard Screws Place nine (9) screws in the holes indicated by circles to secure the motherboard to the chassis. Doing so may damage the motherboard. 22 Chapter 2: Hardware Setup 2. 4 Install a CPU The Socket 370 on the CUV-2LV motherboard supports a Pentium III/Celeron CPU. This section tells you how to install a CPU. The following pictures show the CPU socket location on the motherboard, and the Pin 1 mark on a CPU. CPU Socket Location The CPU socket is located beside the rear panel connectors. Note the Pin 1 location on the socket. Pin 1 CPU Fan Connector CPU Socket 370 CPU Orientation A CPU has a mark (usually a notch or a gold mark) on one corner to help you identify the correct orientation when inserting it to the socket. [. . . ] Connect the IDE cable to the IDE connector at the back of the drive, matching the red pin stripe on the cable with Pin1 on the IDE connector. Connect the power cable labeled P2 to the power connector at the back of the drive. IDE Cable Red Stripe to Pin 1 Power Cable (P2) 42 Chapter 4: Hardware Options Appendix A This appendix gives information on the 250-watt switching power supply that comes with the AVS229NR server. AVS229NR Server User's Manual Power Supply 43 A. 1 General Description The server comes with a 250W ATX power supply with universal AC input that includes PFC and ATX-compliant output cables and connectors. The power supply has an internal cooling fan. The power supply has seven plugs labeled P1 to P7. [. . . ]