User manual ASUS VW190SE

[. . . ] VESA is a registered trademark of the Video Electronics Standards Association. ENERGY STAR® is a registered trademark of the U. S. As an ENERGY STAR® partner, ViewSonic Corporation has determined that this product meets the ENERGY STAR® guidelines for energy efficiency. Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product. [. . . ] Also, displays the control screen for the selected control and toggles between control pairs. ViewSonic VW190SE 7 Do the following to adjust the screen image: 1 To display the Main Menu, press button [1]. NOTE: All OnView menus and adjustment screens disappear automatically after about 30 seconds. This time period is adjustable through the Setup menu and the OSD timeout control described on page 11. 2 3 To highlight a control you want to adjust, press I or J to scroll up or down the Main Menu. To select the highlighted control, press button [2]. A control screen appears like the example shown below. The J down arrow decreases, I up arrow increases The line at the bottom of the screen tells you what you can do next - in this example, either EXIT or select the BRIGHTNESS control. 4 5 To adjust the control, press the up I or down J buttons. To save the adjustments and exit the menu, press button [1] twice. The following tips may help you optimize your display: · Adjust your computer's graphic card so that it outputs a video signal 1280 x 1024 @ 60 Hz to the LCD dislay. (Look for instructions on "changing the refresh rate" in your graphic card's user guide. ) · If necessary, make small adjustments using H. POSITION until the screen image is completely visible. (The black border around the edge of the screen should barely touch the illuminated "active area" of the LCD dislay. ) ViewSonic VW190SE 8 Main Menu Controls Adjust the menu items shown below by using the up Iand down Jbuttons. Control Explanation Auto Adjust automatically sizes, centers, and fine tunes the video signal to eliminate waviness and distortion. Press the [2] button to obtain a sharper image. NOTE: Auto Adjust works with most common video cards. If this function does not work on your LCD dislay, then lower the video refresh rate to 60 Hz and set the resolution to its pre-set value. · If you are using an Macintosh older than G3, you need a Macintosh adapter. Wrong or abnormal colors · If any colors (red, green, or blue) are missing, check the video cable to make sure it is securely connected. Loose or broken pins in the cable connector could cause an improper connection. · Connect the LCD dislay to another computer. · If you have an older graphics card, contact ViewSonic® for a non-DDC adapter. Control buttons do not work · Press only one button at a time. ViewSonic VW190SE 13 Customer Support For technical support or product service, see the table below or contact your reseller. NOTE: You will need the product serial number. Country/ Region United States Canada Web site www. viewsonic. com/ support www. viewsonic. com/ support www. viewsoniceurope. com www. viewsoniceurope. com T = Telephone F = FAX T: (800) 688-6688 F: (909) 468-1202 T: (800) 688-6688 F: (909) 468-1202 T: 0800 833 648 F: (01293) 643910 Contact your reseller Email service. us@ viewsonic. com service. ca@ viewsonic. com service. eu@ viewsoniceurope. com service. eu@ viewsoniceurope. com United Kingdom Europe, Middle East, Baltic countries, and North Africa Australia and New www. viewsonic. com. au Zealand Singapore/ www. viewsonic. com. sg Malaysia/Thailand South Africa/ Other countries Hong Kong www. viewsonic. com www. hk. viewsonic. com T: +61 2 9906 6277 F: +61 2 9906 6377 T: 65 273 4018 F: 65 273 1566 T: 886 2 2246 3456 F: 886 2 8242 3668 T: 886 2 2246 3456 F: 886 2 8242 3668 service@au. viewsonic. com ViewSonic VW190SE 14 Cleaning the LCD Dislay · MAKE SURE THE LCD DISPLAY IS TURNED OFF. · NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE SCREEN OR CASE. To clean the screen: 1 2 Wipe the screen with a clean, soft, lint-free cloth. If still not clean, apply a small amount of non-ammonia, non-alcohol based glass cleaner onto a clean, soft, lint-free cloth, and wipe the screen. To clean the case: 1 2 Use a soft, dry cloth. If still not clean, apply a small amount of a non-ammonia, non-alcohol based, mild non-abrasive detergent onto a clean, soft, lint-free cloth, then wipe the surface. Disclaimer ViewSonic® does not recommend the use of any ammonia or alcohol-based cleaners on the LCD dislay screen or case. [. . . ] Use the following guidelines if it is necessary to replace the original cord set, or if the cord set is not enclosed. The female receptacle of the cord set must meet IEC-60320 requirements and may look like (Figure A1 below): Figure A1 Figure A2 For the United States and Canada In the United States and Canada the male plug is a NEMA5-15 style (Figure A2), UL Listed, and CSA Labeled. For units which are mounted on a desk or table, type SVT or SJT cord sets may be used. For units which sit on the floor, only SJT type cord sets may be used. [. . . ]