User manual ASUS VW220TE

[. . . ] The power supply cord serves as a power disconnect device for pluggable equipment. The socket outlet shall be installed near the equipment and shall be easily accessible. Disclaimer Safety Instructions English 1 Benq LCD Color Monitor User's Guide Table of Contents Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Views of the Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Please follow the steps to install your LCD monitor. 1 . Connect the power cord to ASUS LCD monitor. Connect the audio cable to the Audio Input of Benq LCD monitor. Connect the signal cable to the VGA output of the graphics card on the computer. Connect the audio cable to your computer. Connect the power cord at the back of the monitor to an AC power socket. Please make sure that the socket is not blocked or covered, so you can disconnect the unit from AC supply if you need to. Your monitor is equipped with an automatic power supply for a voltage range from 100 to 240 Volt at a frequency of 50 to 60 Hz. Be sure that your local power is within the supported range. If you are unsure, ask your electricity supplier. Signal Power cord Audio cable English 6 Benq LCD Color Monitor User's Guide Adjusting the Monitor A Look at the Control Panel ikey Exit < > Enter There are 6 keys for user's control including "iKey", "Exit", "Enter", "<" and ">" key and a power swith. The following descriptions are the introduction of these keys & switch. "Power": Turn the power on or off. (Horizontal) Position: adjusts the horizontal position of the display. V. (Vertical) Position: adjusts the vertical position of the display. Phase: adjusts the phase of pixel clock. Pixel Clock: adjusts the frequency of the pixel. English 35 Benq LCD Color Monitor User's Guide 3. Color Adjustment Press "<"or ">" key to select this item and press "Enter" to enter sub-menu. There are four items for color adjustments. There are three items to adjust. Press "<"or ">"key to select a color and press "Enter" to adjust color temperature. 4. Miscellaneous Press "<"or ">"key to select this item and press "Enter" to enter sub-menu. There are three items for miscellaneous. OSD Position : to adjust position of OSD. English 36 Benq LCD Color Monitor User's Guide Language: to select OSD language. OSD Time: to set the standby time of OSD. Volume: to adjust volume of speaker. H. (Horizontal) Position: adjusts the OSD horizontal position of the display. V. (Vertical) Position: adjusts the OSD vertical position of the display. English 37 Benq LCD Color Monitor User's Guide Press "<"or ">"key to select a language then press "Exit" to back to previous menu. 5. Information "Information" sub menu the OSD display the resolution, horizontal and vertical refresh rate. Press "Enter" to recall to factory setings. English 38 Benq LCD Color Monitor User's Guide Troubleshooting Frequently Asked Questions (FAQ) The image is blurred:  Read the chapter, Installation/Adjustment and then select the correct resolution, refresh rate and make adjustments based on these instructions.  Do you use a VGA extension cable?Remove the extension cable for the test. If not, optimize the image working on the description in the chapter, Installation/Adjustment. It is normal for blurring to occur due to conduction losses in extension cables. [. . . ] Press a button on the computer keyboard or move the mouse. If that does not help, then check the VGA cable contacts. If any pins are bent or broken off, then contact your dealer or read the chapter, Additional Help, Repairs & Service. English 39 Benq LCD Color Monitor User's Guide  Is the prompt on the display not illuminated at all?Check the power supply mains socket, the external power supply and the mains switch. [. . . ]