User manual ATIKA BKS 45

[. . . ] Überprüfen Sie die Kettensäge auf: - lose oder beschädigte Sägekette - lose Befestigungen - Verschleiß, insbesondere Kette, Führungsschiene und Kettenrad. EC Declaration of Conformity Extent of delivery Operating times Symbols on the chain saw Symbols Operating instructions Proper use Residual risks Safety instructions - Personal protective clothing - Before sawing - Operating - While sawing - Saw backstroke - General notes - Safe handling with fuels Work instructions (saw techniques) Assembly - Installing the guide bar and the saw chain - Clamping of saw chain Preparing for startup - Chain lubrication - Filling up saw chain oil - Checking the chain lubrication - Fuelling - Mixing - Fuelling the chain saw Inbetriebnahme - Chain brake - Checking the chain brake - Before starting the chain saw - Starten bei kaltem Motor - Stoppen des Motors - Starten bei warmem Motor Start-up - Adjusting the chain lubrication - Saw chain and guide bar - Sharpening of saw chain - Cleaning the guide bar - Chain wheel - Cleaning the air filter - Replacing the fuel filter - Checking/replacing the spark plug - Checking the ignition spark - Chain catcher - Silencer/exhaust outlet - Adjusting the carburetor (idle speed) - Care Transport Storage Guarantee Maintenance and cleaning schedule Possible faults Technical data Description of device / spare parts 17 17 17 18 18 18 18 19 19 19 19 20 20 20 21 21 22 22 22 23 23 23 23 23 23 24 24 24 24 24 24 25 25 25 25 25 25 26 26 26 26 26 27 27 27 27 27 27 27 27 28 29 30 30 KG Schinkelstraße 97 59227 Ahlen - Germany declare under our sole responsibility, that the product Petrol chain saw Type BKS 45 to which this declaration relates corresponds to the relevant basic safety and health requirements of the Directive 98/37/EC, and to the requirements for the other relevant Directives: 2004/108/EG and 2000/14/EG Conformity Assessment Procedures: 2000/14 EEC ­ Appendix V Measured sound power level LWA 113, 7 dB (A). After unpacking, check the contents of the box > > That it is complete Check for possible transport damage Report any damage or missing items to your dealer, supplier or the manufacturer immediately. Complaints made at a later date will not be acknowledged. [. . . ] Consider in this case the balance point of the treetop, neighbour trees, slope direction, state of health of the tree and the wind direction. + Remove interfering branches, scrub and obstacles from the working area at the trunk and make sure that you have a safe standing position. + Thoroughly clean the trunk foot ­ sand, stones and other foreign objects make the saw chain edgeless or may damage it. + Consider the state of health of the tree ­ be careful with trunks with damages or deadwood (droughty, rotten or dead wood). Stop the engine and wear protective gloves whenever working on the guide bar and on the saw chain!Slightly lift the guide bar tip and turn the chain stretching screw (15) clock wisely until the correct chain tension is reached. The saw chain is correctly stretched when it can be lifted in the centre of the chain guide by appr. Cut a kerf with the saw of approximately one third of the tree diameter into the trunk. First of all place the horizontal cut and then as secondly a cut from top in an angle of 45°. Shout the warning "Caution" or "Tree is falling" before starting the fell cut. Turn the chain stretching screw anti-clockwise when the saw chain is stretched too much. Check the saw chain tension: before start of work after the first steps during sawing regularly all 10 minutes Only with a correct clamped saw chain and a sufficient lubrication you can influence the durability. Please observe the following: a new saw chain must be rest retched more frequently. in case of heating of chain to operating temperature it expands and needs to be reclamped. After finishing the sawing works release tension of saw chain as in case of cooling too high tensions would emerge in the saw chain. If chain flackers or comes out of the guide clamp it again immediately. The guarantee expires when using oil which is not allowed for chain saws. Never operate the chain saw without functioning chain lubrication. Check the function of the automatic chain lubrication by switching on the chain saw and holding it with the pike in direction of a carton or paper on the ground. Do not get in contact with the ground with the chain. If an increasing oil track is caused when checking it the oil automatic works faultless. If there is no oil track despite full oil tank: Clean the oil flow channel (19). [. . . ] The carburetor is factory-set to the correct idle speed so that the correct fuel-air mixture is fed to the engine. an incorrect carburetor adjustment results in severe engine damages. Do not continue working with the chain saw in such a condition. In the cases below the carburetor (idle speed) has to be corrected: - Speed too high (saw chain continues to move in idle speed) - Erratic running or lack of acceleration (idle speed too low) - Adjustment to weather conditions and temperatures Contact a specialist workshop and have the carburetor adjustment done. [. . . ]