User manual ATIKA KS 2001

[. . . ] Declaration of conformity Extent of delivery Operating times Symbols on the chain saw Symbols Operating instructions Normal intended use Residual risks Security instructions - Electrical safety Assembly Before the first commissioning - Chain lubrication - Charging the oil tank Commissioning - Mains connection - Mains fuse - Electrical mains supply impedance - Switching On/Off - Chain brake - Checking of chain brake - Clamping of saw chain Working with the chain saw - Before sawing - Saw backstroke - How to avoid backstrokes - General conduct when sawing - Additional advices for sawing trunks - Additional advices for sawing timber under tension/release - Additional advices for chopping down trees Maintenance and cleaning - Maintenance - Sharpening of saw chain - Exchanging saw chain and sword - Chain wheel - Checking of the oil automatic - Cleaning Transport Storage Guarantee Technical data Possible faults Discription of chain saw / Spare parts 17 17 17 18 18 18 18 18 20 20 20 20 20 21 21 21 21 21 21 21 21 22 22 22 22 22 23 23 23 24 24 24 24 24 24 25 25 25 25 25 26 26 / 155 KG Schinkelstraße 97 59229 Ahlen - Germany declare under our sole responsibility, that the product chain saw typ KS 2000/40 to which this declaration relates corresponds to the relevant basic safety and health requirements of the Directive 98/37/EC, and to the requirements for the other relevant Directives: 2004/108/EG, 73/23/EWG. Measured sound power level LWA 103 dB (A) and guaranteed sound power level LWA 105 dB (A). That it is complete Check for possible transport damage Report any damage or missing items to your dealer, supplier or the manufacturer immediately. Complaints made at a later date will not be acknowledged. [. . . ] 230 V with the mains voltage and connect the saw to the relevant and properly earthed plug. Use a shockproof plug, mains voltage 230 V with residual current circuit breaker (FI switch 30 mA). Only use connection cables with sufficient diameters. 2 = Chain brake active Chain saw does not initiate Set the chain brake release (3) in pos. When conditions in the electrical mains supply are unfavourable, voltage reductions for short periods can occur during the process of turning on the equipment, which can adversely affect other equipment (e. No breakdowns are to be expected if the maximum, electrical mains supply impedances given in the table are met. Check the saw chain tension before start of work after the first steps during sawing regularly all 10 minutes  Only with a correct clamped saw chain and a sufficient lubrication you can influence the durability. A new saw chain must be reclamped more often until it has elongated. in case of heating of chain to operating temperature it expands and needs to be reclamped. After finishing the sawing works release tension of saw chain as in case of cooling too high tensions would emerge in the saw chain. If chain flackers or comes out of the guide clamp it again immediately. Do not use the chain saw for lifting or moving of wood. Make sure that the wood is free of foreign object (stones, nails etc). Hold the chain saw always firmly with both hands, left hand on the front handhold (4) and right hand on the rear handhold (17). 14 Make sure that the wood can not turn when sawing. There is risk of injury by wood pieces carried away. Initiate saw chain before getting in contact with the wood. Only cut the sawing material with the lower edge. Cutting with the upper edge causes saw backstrokes. Put on the chain saw as plane as possible. Use the claw stopper (16) for fixing the chain saw on the wood. Use the claw stopper when sawing as lever. [. . . ] water , solvents and polishing agents shall not be applied. Pay attention to that the ventilation slots for the motor cooling are free (risk of overheating). After a lomger application period (1 ­ 3 hours) disassemble the cover, the sword and the chain and clean them with a brush. 24 In case of harder pollution or resins put the chain for some hours in a container with chain cleaner. [. . . ]