User manual ATX KT266 PRO

[. . . ] Introduction The K7T266 Pro (MS-6380) ATX mainboard is a high-performance computer mainboard based on VIA® Apollo KT266 chipset and designed for the AMD® Athlon or Duron (PGA) processor for inexpensive business/ personal desktop markets. The Apollo KT266 chipset consists of the VT8366 Super Northbridge and the VT8233 Southbridge. VT8366 provides a PC1600/2100 DDR (Double Data Rate) solution with support for 200/266MHz Front Side Bus. By using PC2100 DDR technology, the VT8366 enables 2. 1GB/second peak bandwidth between system memory and Northbridge. [. . . ] Select Yes only when you install and use mono display adapter card. 3-14 AMI® BIOS Setup PCI Delay Transaction The chipset has an embedded 32-bit posted write buffer to support delayed transactions cycles. Select Enabled to support compliance with PCI specification version 2. 1. Settings are Enabled and Disabled (default). BIOS Protection Setting to Enabled will prevent BIOS from performing any BIOS update/ flash utility. Settings are Enabled (default) and Disabled. 3-15 Chapter 3 Power Management Setup AMIBIOS SETUP - POWER MANAGEMENT SETUP (C)2001 American Megatrends, Inc. All Rights Reserved IPCA Function ACPI Standby State USB Wakeup From S3 Power Management/APM Green PC LED Status Suspend Time Out (Minute) Display Activity IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ13 IRQ14 IRQ15 CPU Critical Temperature Power Button Function Restore on AC/Power Loss :Yes :S1/POS :Disabled :Enabled :Dual Color :Disabled :Ignore :Monitor :Monitor :Ignore :Monitor :Ignore :Ignore :Ignore :Ignore :Monitor :Ignore :Disabled :Suspend :Last State Wake Up On Ring Wake Up On PME# Resume By Alarm Alarm Date Alarm Hour Alarm Minute Alarm Second :Disabled :Disabled :Disabled :15 :12 :30 :30 ESC : Quit : Select Item F1 : Help PU/PD/+/-:Modify F5 : Load Previous Values F6 : Load Fail-Safe Defaults F7 : Load Optimized Defaults IPCA Function This item is to activate the ACPI (Advanced Configuration and Power Management Interface) Function. If your operating system is ACPI-aware, such as Windows 98SE/2000/ME, select Yes. ACPI Standby State This item specifies the power saving modes for ACPI function. Options are: S1/POS S3/STR The S1 sleep mode is a low power state. In this state, no system context is lost (CPU or chipset) and hardware maintains all system context. The S3 sleep mode is a lower power state where the information of system cofiguration and open applications/files is saved to main memory that remains 3-16 AMI® BIOS Setup powered while most other hardware components turn off to save energy. The information stored in memory will be used to restore the system when an wake up event occurs. USB Wakeup From S3 This item allows the activity of the USB device to wake up the system from S3 sleep states. S3 is one of the system states for ACPI, which saves different amount of system power. Power Management/APM Setting to Enabled will activate the Advanced Power Management (APM) features to enhance power saving modes. Green PC LED Status This item configures how the system uses sleep state LED on the case to indicate the sleep state. Available options are: Blinking The sleep state LED blinks to indicate the sleep state. Not Changed The sleep state LED remains the same color. Dual Color The sleep state LED changes its color to indicate the sleep state. Display Activity/IRQ3/IRQ4/IRQ5/IRQ7/IRQ9/IRQ10/IRQ11/IRQ13/ IRQ14/IRQ15 These items specify if the BIOS will monitor the activity of the specified hardware peripheral or component. If set to Monitor, any activity detected on the specified hardware peripheral or component will wake up the system or prevent the system from entering the power saving modes. The default values for different items are listed below: 3-17 Chapter 3 Display Activity IRQ3 IRQ4 IRQ5 IRQ7 IRQ9 IRQ10 IRQ11 IRQ13 IRQ14 IRQ15 Ignore Monitor Monitor Ignore Monitor Ignore Ignore Ignore Ignore Monitor Ignore Note: IRQ (Interrup Request) lines are system resources allocated to I/O devices. [. . . ] All clients which would like to access Internet resources through USB cable should have installed GeneLinkTM driver. Now we need to make some network configurations on the Desktop/ Notebook which connect to GeneLinkTM Software Router to make your Internet access possible (maybe you need to consult you Network Administrator for doing that): a. If your existing home/office network is NOT using DHCP to assign clients IP address, your need to: - Move your mouse pointer on Network Neighborhood icon and right click on it. a. A-6 USB PC to PC Networking Function - Click on Properties, youll see another menu. - Choose TCP/IP in Configuration tag, and then press Properties button. [. . . ]