User manual AUDIO DESIGN LA-2000MD

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual AUDIO DESIGN LA-2000MD. We hope that this AUDIO DESIGN LA-2000MD user guide will be useful to you.

Lastmanuals help download the user guide AUDIO DESIGN LA-2000MD.


Mode d'emploi AUDIO DESIGN LA-2000MD
Download
Manual abstract: user guide AUDIO DESIGN LA-2000MD

Detailed instructions for use are in the User's Guide.

[. . . ] Prepare the power cable for attachment to the amplifier by stripping 1/2" of insulation from the end of the wire. Trim the power cable within 18" of the battery and strip1/2"of insulation from the end of the wire. Strip 1/2" from the battery end of the power cable and crimp a large ring terminal to the cable. NOTE: ALWAYS protect the battery and electrical system from damage with proper fusing. [. . . ] If noise is still present, contact your local authorized dealer or Lightning Audio customer service. When using a Master/Slave setup do not exceed more than two amplifiers. Strip the speaker wires 1/2" and insert into the speaker terminal and tighten the setscrew to secure into place. Be sure to maintain proper speaker polarity. DO NOT chassis ground any of the speaker leads as unstable operation may result. Check all power and ground connections for frayed wires and loose connections. Complete the installation by installing the proper value fuse. Operation Adjusting Level: To adjust the level setting, turn the amplifier gain level to the lowest setting. Turn the source unit volume up until distortion is audible and then slowly down until the distortion is inaudible (approximately ¾ volume position). Next, increase the amplifier level setting until once again distortion is audible and then down slowly until the distortion is inaudible. NOTE: Proper level setting is done by a trained professional utilizing an oscilloscope. for a more in depth setting procedure , contact Lightning Audio Technical Support. In a Master/Slave setup ONLY adjustments made to the master amplifier will effect the output. With the system playing at normal listening level, turn the crossover adjustment knob up slowly until the desired crossover point is achieved. Example: subwoofers- low pass with an 80Hz crossover point and full-range- high pass with a 100Hz crossover point NOTE: Some models include a subsonic filter with a variable 15-40Hz high pass filter designed to prevent frequencies below the audio range from being applied to the subwoofer from the amplifier. Set this to your personal preference while listening to the system. In a Master/Slave setup ONLY adjustments made to the master amplifier will effect the output. Amplifier does not turn on B+ or REM not between 10. [. . . ] Any product not purchased from an authorized Lightning Audio Dealer · Limit on implied warranties Any implied warranties of fitness for use and merchantability are limited in duration to the period of the express warranty set forth above. Some states do not allow limitations on the length of an implied warranty, so this limitation may not apply. No person is authorized to assume for Lightning Audio any other liability in connection with the sale of the product. ⷠHow to obtain service Defective products should be returned to your local authorized Lightning Audio Dealer for warranty service or, you may call 1-888881-8186 for Lightning Audio customer service. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AUDIO DESIGN LA-2000MD

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual AUDIO DESIGN LA-2000MD will begin.

Search for a user manual

 

Copyright © 2015 - LastManuals - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.

flag