User manual AUDIOLAB 8000M

[. . . ] Audiolab IAG House, Sovereign Court, Ermine Business Park, Huntingdon PE29 6XU Tel: 01480 447700 Fax: 01480 431767 User Instructions 8000M 8000P 8000Q audiolab 8: Warranty Audiolab limited warranty Audiolab Ltd. warrants this product, subject to the terms and conditions below, to be free from defects in materials and workmanship. During the warranty period Audiolab will repair or replace (at Audiolab's option) this product, or any defective part in this product, if it is found to be defective due to faulty materials, workmanship or function. The warranty period may vary from country to country. [. . . ] The wider blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. Class II construction double insulated. These products must not be connected to earth. Power Cord: An AC power cord is normally supplied with a mains plug suitable for your area. If you have any doubts, consult your dealer about obtaining a suitable power cord. Important notice to UK users The appliance cord is terminated with a UK approved mains plug fitted with a 5A fuse. If the fuse needs to be replaced, an ASTA or BSI approved BS1362 fuse rated at 5A must be used. If you need to change the mains plug, remove the fuse and dispose of this plug safely immediately after cutting it from the cord. Connecting a Mains Plug The wires in the mains lead are colouredin accordancewith the code: Blue: NEUTRAL; Brown: LIVE: As these colours may not correspond to the coloured markings identifying the terminalsin your plug, proceedas follows: The BLUE wire must be connected to the terminal marked with the letter N or coloured BLUE or BLACK. The BROWN wire must be connected to the terminal marked with the letter L or coloured BROWNor RED. 5A FUSE BS 1362 BLUE (Neutral) BROWN (Live) 7: Specifications 8000Q Pre-amplifier Inputs: Gain and Sensitivity CD, TUNER, AUX, VIDEO, TAPE 1, TAPE 2: IMPEDANCE: 20k GAIN: Adjustable by 3dB steps 0 -15dB. , corresponding to SENSITIVITY(nom. ): 100, 140mV, 200mV, 283mV, 400mV, 562mV HEADPHONES: Gain adjustable 18dB - 33dB in 3dB steps Signal To Noise Ratio (IHF, rel. 0. 5V output) Any input, any gain setting: 97dB Headphones: 80dB Frequency Response 10 Hz-20 kHz ±0. 2 dB: 1 Hz-75 kHz -3 dB. Total Harmonic Distortion & Noise Less than 0. 007 % ref 7. 7V rms, 20Hz - 20kHz Channel Balance Within 1 dB Channel Separation Better than100 dB @ 1 kHz any input, any setting Pre-amp Output Max. Output >7. 7 V RMS (20dBm); Output impedance 75 Headphone Output >7. 7Vrms;100 (for headphones 8 -2 k impedance) Record Output VIDEO OUT, TAPE 1 OUT, TAPE 2 OUT: Gain 0 dB (x1); 100 Muting Attenuation>63 dB, controlled automatically Operating Temperature Range 10-35 °C Power Requirements (Depending on Region) 50-60Hz 100V, 110-120V, and 220-240V models available Maximum Power Consumption: 15 VA Dimensions (WXHXD) 445x74x335 mm - including feet, terminals and controls 445 x 64 x 302 mm- excluding feet, terminals and controls Weight Net: 6 kg Shipping:7. 3 kg 8000P Power Amplifier Rated Output Power 100W (20dBW) /Channel into 8 both channels driven Input 1V rms for 100W into 8 Input Impedance: 50k Load Connected in parallel with INPUT Gain 29. 0 dB at1kHz Signal To Noise Ratio (IHF, rel. 0. dBW) Better than 95 dB Frequency Response 20 Hz-20 kHz ±0. 3 dB 0. 1 Hz-75 kHz -3 dB. Total Harmonic Distortion & Noise Less than 0. 05 % Channel Balance Within 1 dB Polarity (Phase) Non-Inverting Muting Muting controlled automatically Operating Temperature Range 10-35 °C Power Requirements (Depending on Region) 50-60 Hz 100V, 110-120V, and 220-240V models available Maximum Power Consumption: 500 VA Dimensions (WXHXD) 445x74x337 mm - including feet, terminals and controls 445 x 64 x 302 mm- excluding feet, terminals and controls Weight Net: 8. 7 kg Shipping:10 kg 8000M Power Amplifier Rated Output Power 125W (21dBW) /Channel into 8 , 20Hz - 20kHz Input Sensitivity 1. 12V rms for 120W into 8 Input Impedance: 50k Load Connected in parallel with INPUT Gain 29. 0 dB at1kHz Signal To Noise Ratio (IHF, rel. 0. dBW) Better than 96 dB Frequency Response 20 Hz-20 kHz ±0. 3 dB 0. 1 Hz-75 kHz -3 dB. Total Harmonic Distortion & Noise Less than 0. 05 % Polarity (Phase) Non-Inverting Muting Muting controlled automatically Operating Temperature Range 10-35 °C Power Requirements (Depending on Region) 50-60Hz 100V, 110-120V, and 220-240V models available Maximum Power Consumption: 300 VA Dimensions (WXHXD) 445x74x337 mm - including feet, terminals and controls 445 x 64 x 302 mm- excluding feet, terminals and controls Weight Net: 8. 2 kg Shipping:9. 6 kg Audiolab reserves the right to alter design and specification without notice. Specification may vary for different countries. Audiolab is a member of the International Audio Group. 5: Operation Switching On Make sure all the signal and loudspeaker connections to and from the amp are secure and correctly made. 15 Walpole Park South Walpole MA 02081 USA Tel: +1 508 850 3950 Fax +1 508 850 3905 Servicing Servicing of Audiolab products should only be carried out by authorised service agents. If service is required the equipment should be returned, securely packaged, preferably using original packaging, to your dealer. In the UK equipment may be returned to the IAG Service Centre. [. . . ] Both the 8000M and the 8000P can be used in conjunction with the 8000S integrated amplifier for multi-amping. Combinations of amplifiers in a multi-channel system should have the same gain and phase characteristics or imbalance will result. We recommend the use of Audiolab amplifiers throughout such a system. Current Audiolab amplifiers are gain and phase compatible with previous models. [. . . ]