User manual AUDIOVOX 1284540

[. . . ] ® CCS-100 ELECTRO CONTR NTROL ELECTRO NIC CRUISE CONTROL INSTALLATIO MANUAL ALLATI INSTALLATIO N M ANUAL INDEX Page 1. Cruise Control Installation: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Throttle Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Route the 6 wires from the switch to the control switch connector from the cruise control main wiring harness. Be sure to avoid any sharp or moving surfaces when routing wires, and secure the wires along their path using tie straps. Plug the terminated ends of the Red, Brown, Green and Yellow wires into the color coded locations on the connector. Be sure that the terminals click, and are fully seated in the connector. Plug the switch connector into the mating connector on the main cruise control harness. Connect the Black wire from the switch to a known chassis ground source. Connect the Grey wire from the switch to the parking light wire in the vehicle. When probed, the parking light wire will read +12 VDC when the parking lights are on, and 0 VDC when the parking lights are off. The Grey wire controls the backlighting of the switch, and the switch will not illuminate if the Grey wire is left disconnected. You must connect all other wires from the switch, or the cruise control will not operate. -8- Figure 1 Carefully cut-out along dotted lines and place on selected area. DASH BOARD TEMPLATE Drill 1/4" Dia. holes, (2 places). Use a file or razor knife to remove the material between the 2 holes. Figure 2 CONTROL SWITCH MOUNTING DASH TEMPLATE CUT-OUT CONTROL SWITCH E ACC L E CRUIS ON OFF OL CONTR S RE T SE ST COA Figure 3 CONTROL SWITCH CONNECTIONS CONNECTOR 1 3 RED WN BRO EN GRE LOW YEL 4 -9- 2 ROAD TESTING THE CRUISE CONTROL Be sure to fully test all functions of your new cruise control on a level surface away from predestrian and vehicle traffic. Unit will engage when Set button is released. To disengage, tap on brake or turn switch off - cruise will disengage. If unit is inoperative, open cover on cruise and look at the L. E. D. If the vehicle's speed drops considerably when travelling up hills, you may need the optional vacuum booster canister. Call 1 - 800 - 225 - 6074 for additional assistance. ON / OFF : Move the ON / OFF switch to the ON position. Nothing will happen, as this simply prepares the system for operation. Each time the ignition switch or the cruise control switch is turned OFF, the system is de - energized. To reenergize the system, the ignition switch must be turned on, and the cruise control switch must be moved to the ON position. The cruise control switch can be left On at all times without causing any damage to the system. SET SPEED : After turning the system On, wait at least 3 seconds before attempting to set your speed. [. . . ] Be sure bracket is mounted securely so it will not vibrate during vehicle movement. NOTICE: If the speed sensor coil is closer than 1/4", there is a possibility that the magnets will strike the coil. If the coil is more than 1/2" from the magnets, the cruise control may not function properly. NOTE: Make sure the black and gray wires are routed clear of any hot or moving parts as well, away from electrical items such as spark plug wires or ignition systems. [. . . ]