User manual AUDIOVOX 1285376

[. . . ] In addition, the chart on the last page of this manual has a section for the particular features and options installed in your vehicle as well as the override method selected. Valet Switch manual override is pre-selected from the factory, however, the system can be configured for "Custom Code" operation. Confirm the override mode selected on the last page of this manual and familiarize yourself with the selection on it's operation. FEATURES : w w w w w w w w w w w w w w w w w w w w w w w w w w w w w w w w w w w 2 Four Button Programmable RF Transmitters (capable of accepting 4 transmitters) Four Channel Receiver Anti Code Grabbing Technology Selectable Manual Override Mode Remote Panic in all modes Protected Valet User Programmable Manual Override Code 7 Function LED (Light Emitting Diode) - Arm / Disarm / Zone 1, 2, 3 / Valet / Arming Intrusion Alert with Memory Audible Arm / Disarm / Defective Zone / Tamper Confirmation Instant Siren Activation Starter Disable (Optional relay required) Additional Engine Immobilizer Output (optional relay required) True Last Door Arming (hardwire only) Defective Zone By-Pass Hardwire or Voltage Sense Selectable Active or Passive Arming Selectable Programmable Auto Lock On / Off Programmable Auto Unlock On / Off Programmable Door Lock Pulse Duration 1 Second / 3. 5 Seconds /1 Sec L/ Dbl. U/L Programmable Active or Passive Door Locks User Programmable Permanent Chirp Delete On Command RF Chirp Delete from Transmitter 6 Tone Multi-Tone Siren RF Inhibit with ignition on Parking Light Flasher Plug In Dual Stage Shock Sensor Starter Disable Remote Trunk Release (must have electronic trunk release) Remote Keyless Entry (must have power door locks) Multiple Vehicle Capable Remote Starter Remote Power Window Roll Up Remote Garage Door Interface Two Step Unlock Configurable OPTIONS : YOUR "ANTI CODE GRABBING" TRANSMITTERS The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system. [. . . ] If the siren sounds 4 chirps, then the alarm was triggered in your absence. Before turning the key on, examine the LED and refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was triggered. If the siren did not sound when disarming, then the chirps have been turned off, and you should refer to the section titled "ELIMINATING THE ARM / DISARM CHIRPS" in this manual. o Doors Unlock - Optional Note:If the optional 2 step door unlock circuit is installed, when the unlock transmitter button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. If your transmitter has a separate lock unlock buttons, pressing the unlock button anytime after the first unlock command will cause all the vehicle doors to unlock. As you approach the vehicle, press and hold the Unlock button on the keychain transmitter for 2 seconds. If passive arming was selected during the installation, then the LED will start flashing rapidly, indicating that the system is re arming automatically. Open any door to suspend the automatic arming. If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the key on, examine the LED to identify which zone was triggered. If the siren sounds 4 chirps, then the alarm was triggered in your absence. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. If your system has been selected for Valet Switch manual override as indicated on the last page of this manual, to by-pass the alarm system. Turn the ignition key to the on position. Within 5 seconds, press and release the valet push button switch. The alarm system will stop sounding and enter the disarmed mode. You can now start and operate the vehicle normally. Typically this override mode is used only if the transmitter has become inoperative. You may elect to enter the VALET mode until repair or replacement of the transmitter, after which, returning the system to the full operation mode is necessary. To do so, see item 3 under the heading VALET SWITCH. Programming Your Custom Override Code: Unlike override switches easily found, and defeated, this security system allows the consumer to program a personal override code, offering a higher level of security. To take advantage of this option, programmable feature # 10 must be selected for the Custom Code Option. [. . . ] 3) Within 5 seconds, turn the ignition switch off then on. 4) Within 5 seconds, press and release the pushbutton switch 1 time. 5) Turn the ignition switch off then on and start the vehicle. Note:If you have changed the programmed override code then substitute your new code tenths for step 2 above, and units for step 5 above. [. . . ]