User manual AUDIOVOX 1286504A

[. . . ] Model APS-55LRa Installation Manual 3 Channel Remote Start / Keyless Entry System Installation Instructions This Unit Is Intended For Installation In Vehicles With 12 Volt Negative Ground Electrical Systems, Gasoline or Diesel With True Tach Reference And Automatic Transmissions Only. Kit Contents (1) - APS-55LRa Control Module (2) - 3 Button High Frequency Transmitters (1) - 3 Channel Code Learning Receiver (1) - Multi Pin Input/Output Harness (1) - Six Pin Power Harness (1) - Two Pin I/O Harness Factory Alarm By-Pass and Diesel Wait To Start Input (1) - 2 Pin Door Lock Harness (2) - 30 Amp In-line Fuse Holders With Fuses (1) - Control Switch (1) - Programming Switch (1) - Ring Terminal (4) - 1/2" Long Screws (1) - Pin Switch (1) - Remote Start Warning Label (1) - Literature Package Revision A: Changed text on page 10, Step # 5 9-22-03. 128-6504A 1 of 16 The APS-55 Remote Start/Keyless Entry System is designed for use with Automatic Transmission Vehicles Only!The unit provides wait to start input for glow plug pre-heat which will be used for all diesel applications. If this wire is not connected, then the unit will remain in the Gasoline mode setting, which will crank the car when the RF signal is received with no delay. Regardless of the vehicle, Gasoline or Diesel, for every installation, the vehicle MUST HAVE a Tach Signal Input, and an Automatic Transmission. INSTALLATION OF THE MAJOR COMPONENTS: CONTROL MODULE: Select a mounting location inside the passenger compartment (up behind the dashboard). [. . . ] Connect the Green wire to the low current ground signal wire from the factory door unlock switch to the factory door unlock relay. See Below For Wiring Detail. 3 Wire Ground Switched Door Lock/Unlock Wiring Detail 3 Wire Positive Switched Door Locks: In this application, the Red wire of the two pin harness provides a + 12 volt pulse during the disarming sequence, or pulsed 12 volt unlock output. Connect the Red wire to the low current 12 volt signal wire from the factory door unlock switch to the factory door unlock relay. The Green wire of the two pin harness provides a + 12 volt pulse during the arming sequence or pulsed 12 volt lock output. Connect the Green wire to the low current 12 volt signal wire from the factory door lock switch to the factory door lock relay. See Below For Wiring Detail. 3 Wire Positive Switched Door Lock/Unlock Wiring Detail 9 128-6504A 9 of 16 Resistive Circuits, As Well As 4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt Door Lock Control Circuits These applications require the use of additional components which may include relays, fixed resistors, or for convenience, the AS 9159 Door Lock Interface. Refer to the AUDIOVOX Door Lock Wiring Supplement and or the Audiovox fax back service for information on your particular vehicle for properly connecting to these types of circuits. 2 Pin Blue Connector : Programming Switch Route the gray and black wires in the 2 pin connector from the previously installed programming switch to the control module and plug it into the mating blue connector on the side of the module. 3 Pin Antenna/Receiver Connector: (White Connector) Plug the previously routed three pin connector from the antenna receiver assemble into the mating connector of the control module. This connector supplies 12 volts, ground and RF data from the antenna receiver to the remote start module. Be certain this connector is firmly seated making good contact to the control unit. 1. RF Programmable Features: Feature Selection 1 Flash 1 Run Time 5 Min. 2 During Crank Off 3 Light Output During Run Steady 4 Tach Mode NA 5 Voltage Level NA 2 Flash 10 Min. On Flash Tach NA 3 Flash 15 Min. 4 Flash 20 Min. Default 10 Min. 5. Trouble Shooting Door Locks Crank Time Gas/Diesel Off 1 Sec/1 Sec 0. 8Sec Gas On 3. 5 Sec/3. 5 Sec 1. 0 Sec Diesel 10 1 Sec/Dbl 1 Sec 1. 5 Sec Diesel 15 2. 0 Sec Diesel 20 Off 1 Sec/1 Sec 1. 0 Gas To program these selectable features: Turn the ignition key to the ON position. Press and release the program switch 3 times. Immediately turn the ignition key OFF, then back to ON. Press and release the program switch 2 times Use the Start button on the transmitter to advance to the feature that you want to change. EXAMPLE - If you need to change programmable feature number 3, press and release the start button on the transmitter 3 times in succession. The parking lights will flash 3 times confirming that selected feature 3 can now be programmed. Use Lock button on the transmitter to change the selection of the programmable feature. If you are not sure what the setting for any feature is, press the lock button 1 one time, the parking lights will flash once or twice indicating the features setting. NOTE: Once you enter the feature-programming mode, do not allow more that 15 seconds to pass between steps, or the programming will be terminated. NOTE: If the Glow Plug sense wire, Green/Yellow is connected, this wire will have priority over the setting of feature #8. [. . . ] The cathode (Striped) side must be connected to the hood pin switch. If the hood pin switch is also used for an alarm trigger input, be certain to use the dual diode assembly packaged with the Audiovox Remote Start Unit as shown below. METHOD 2 To connect to the key in sensor circuit as shown for method 2: A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. Cut this wire and connect the ignition cylinder side to chassis ground. [. . . ]