User manual AUDIOVOX AOS-44

[. . . ] Please install this system according to the instructions in this manual. Do not disassemble the camera or the monitor. This voids tile warranty Disassembling the camera ~II compromise the waterproof seal. . . Connect the system to an ignition switched power source. [. . . ] Use a compression plate to attach the monitor bracket to the dash or overhead (See Fig 4). Adjust mounting angle of the monitor to allow driver to easily view the screen from all seat positions (See FIg. If necessary, snap sun visor into groove on front face of monitor. Press all (4) ~es of the visor to snap it into place. OCA-80 cABLe 1. The camera-to-cable connection is waterproof. The cable-lo-monitor co, lnectiOI1 is not waterproof. The cylindrical end attaches to the camera. The rectangular box end attaches 10 the monitor. Do not run ttle OCA-80 cable over sharp edges or corners. keep the cableol away from hot and rotating parts. Place 811eKCess cable in convolllted tu~ng 4. Wire tie the cable securely. -Page 20( 14 - AOS-44 Operations Manual MAINTENANCE: Remove dus18nd dirt wi\t) a damp soft cloth. Heavier dirt should be remolJed with 3 damp soft cloth and mild detergent Do not use strong cleaning agents containing gasoline, ttlinner, benzene or alcohol. These substances may damage the extelior surface of the monitor . B&fore drilling, be sure no cable or wiring is on the other we, Be sure to drill a 19mm 13/4"1 diameter hole only ~ Feed as much cable as possible into vehicle and clamp securely, This reduces the possibility of being hooked 3. 5, WIRING during production, Keep 8!1 cables away from HOT, ROTATING and ELECTRICALLY NOISY components To increase protection 01 cable, place all excess ~re and extension cable in convoluted tubing Do not twist camera cable and do not cut camera pigtail or cable CAMERA AND MONrrOR 2. 3. 4. See wiring diagram for connections to igni1ion, ground and back-up circuit (See Fig 6} Wiring camera: Drill a 19mm13/4" I diameter hole into vehicle body near the camera and bracket Connect camera connector to extension cable in vehicle. Push extra cable into vehi-;le (Be careful not to kink cable) and fit grommet into hole. Apply sealant around grommet to increase resistance to wclter penetration. Wiring Monitor: Insert exte!\sion c"b\e into camera . 1 posibon \1 {2) camera$ are u$ed, be $ure to mar~ each extension cable properly and plug second cable into camera #2 position Bundle excess cable together using a cable tie or vinyl tape. This will avoid possible damage to cable during operation. The red W;re marked ACC is connected to an ignmon power source, the black W;re marked GND is connected to cha$sis ground, and tt\e blue wire marked BACK is connected to the vehicle's back up circuit FUNCT1ONS AND OPERATlON Monitor' see page l' 1 Power switch: 2. Monitor operates when vehicle transmission is switched into "REVERSE" ON -Monitor and system operate when ignition switch is . ON" UP -Panoramic 'v-iewof the horizon, if camera is in "UP" position DOWN -Directed 'v-iew the rear of the vehicle, if camera is in "DOWN" posi!ion of "A" -used mainly for rear mounted camera Or as specified by the installer. [. . . ] 1 camera Rated voltage Operating voltage Current consumpbon 12 Jolt DC, negative ground 11 to 30 volt DC 1. 5 amperes AOC-75 Camera SensitMty Signal system Image sensor Viewing angle Outer dimensions 0. 11ux NTSC 1/3. BN'J CCD w/electronjc auto-iris 270K picture elements 110 degrees (H). 90 degrees (V) 2. 44- X 1 50" X 1. 96- (W X H x D) 6. 20 cm x 381 cm x 4. 98 cm (W kH X D) 0. 8Ibs. 036 Kg Weight AOM-53 Monitor Signal System Picture tube Outer dimensions Weight NT~C 5. 5. [. . . ]