User manual AUDIOVOX AVP-8380T

[. . . ] VIDEO CASSETTE PLAYER MODEL AVP-8380T OPERATING INSTRUCTIONS CAUTIONS AND WARNINGS To obtain the best results and to avoid malfunctions, PLEASE READ CAREFULLY THE DESCRIPTIONS AND OPERATING PROCEDURES CONTAINED IN THIS OWNER'S MANUAL PRIOR TO OPERATING THE VIDEO CASSETTE PLAYER. This user manual employs the following symbols to indicate different types of warning messages. Indicates a warning or notice regarding product operation. Indicates the presence of important operating and maintenance (servicing) instructions. Indicates the presence of un-insulated dangerous voltage within the unit enclosure. CAUTION RISK OF ELECTRIC SHOCKS DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER. [. . . ] The tape will play to the end, rewind to the beginning and play again. 2 AUDIO/VIDEO IN Jacks Connect these jacks to the audio/video out jacks terminal of your Game machine or Camcorder using the RCA cord provided. 9 CONTROLS AND INDICATORS (CONTINUED) REAR PANEL !IN Connector Connect the TV antenna (or cable if available - home use) to this connector. @ Infrared (IR) INPUT Connector This connector provides a two-wire interface with various Audiovox IR products such as VOH-681/682. (P/N 136B1864) * Connector description # DC 12V Jack When using a DC power source, connect this jack to 12V DC. * Connector description 10 CONTROLS AND INDICATORS (CONTINUED) $ AUDIO/VIDEO OUT Connectors These connectors provide an interface to the AUDIO/VIDEO IN connectors of your video monitor, using an RCA cord. % AUDIO/VIDEO IN Connector These connectors provide an interface to the AUDIO/VIDEO OUT connectors of your Game machine or Camcorder using an RCA cord. ^ Infrared (IR) INPUT Connector (3. 5mm jack) This connector provides a three-wire interface with receiver accessory. (P/N 136-B2129) CAUTION: This VCP is for 12Vdc use only; DO NOT use in 24Vdc vehicles. If you use this unit in a 24Vdc vehicle, all the indicator lamps will blink indicating a major malfunction. Disconnect the plug from the power source immediately. 11 THE REMOTE CONTROL UNITS Power ON/OFF Selects playback audio (Hi-Fi Used to eject the cassette tape In STOP mode use this button to select between the video line inputs and VCP's tuner. In PLAY mode use this button to adjust the tracking. Reverse picture search in playback mode & Rewind in stop mode Playback & Retracking in playback mode Forward picture search in playback mode & Fast forward in stop mode Auto repeat ON/OFF Still playback in VCP mode The tape is stopped Slow motion during play or play-pause mode Display the time counter position and clear the display Auto channel search and memory Add or remove channels after auto channel memory Exit auto channel memory and add/remove mode Number buttons. Hi-Fi "L" Hi-Fi "R" MONO . . . ) Selects between the video line input and VCP's tuner 12 CONTROLS AND INDICATORS (CONTINUED) REMOTE CONTROL BATTERY REPLACEMENT REMOTE CONTROL (backside) Before attempting to operate your Remote Control, install the batteries as described below. Using a fingernail, lift the battery cover up and off. 2 Install the 3V Lithium Cell battery as shown. Make sure that proper polarity (+) is observed. NOTE : Insert the battery beneath the battery case holding pins. 3 Close the battery cover. LIT UM CELL HI CR2025 + battery COVER 3V 13 GETTING STARTED VCP TO VEHICLE CONNECTION · Connect the unit to a 12Vdc source only. · The unit should be connected to the vehicle only after verifying the polarity of the cigarette lighter socket. (12Vdc with negative ground) 14 GETTING STARTED (CONTINUED) 12 VOLT POWER NOTES · This VCP operates on 12Vdc only. If you apply more than 18Vdc, the VCP will automatically turn off. · If the polarity is reversed, the unit will not operate. [. . . ] · Check connector between VCP and TV. · Check connection(a). · Check cable/by pass or continuity test. · Clean head using tape cartridge cleaner. We recommend using cartridge with cloth or paper tape and cleaning drops included. [. . . ]