User manual AUDIOVOX AWM820

[. . . ] IMPORTANT NOTES *Avoid installing the unit in locations described below: - Places exposed to direct sunlight or close to heat radiating appliances such as electric heaters - On top of other stereo equipment that radiates too much heat - Places lacking ventilation or dusty places - Humid or moist places *Read Owner's Manual before operating *Be sure all connections are properly made before turning power on. IDENTIFICATION OF CONTROLS / CONNECTIONS 22 21 20 1 19 234 5 6 18 17 16 15 14 7 8 9 10 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) 11) 12) 13) 14) 15) 16) 17) 18) 19) 20) 21) 22) Tuning Up / Minute Set Button Tuning Down / Hour Set Button Mute / AS/PS / Loud Buttons Time Set Button Display Window Alarm Set / Alarm On/Off Buttons Button Reset Preset Buttons Cassette Fast Forward Button Cassette Rewind Button Cassette Player Cassette Eject Button Speaker Selector 1/8" Auxiliary Input Jack Stereo Headphone Jack Audio Adjust Button Power Switch w/Volume Control Source Selectors Car Antenna Jack 75 FM Antenna Terminals RCA Auxiliary Input Terminals Harness 13 12 11 1 INSTALLATION AND HOOK UP 1) Cut mounting hole in desired location using mounting hole diagram (right). 2) Route power, speaker, and antenna cables through hole, and connect to unit as shown in hook up diagram below. 3) After making sure connections are correct, test unit operation as described in the operation section (Do not mount until AM antenna trimmer adjustment has been made. WIRING COLOR CODE FOR AWM-820 COLOR ORANGE/WHITE GREEN/WHITE BLACK/WHITE WHITE VIOLET BLUE LIGHT GREEN RED VIOLET/BLACK YELLOW LT. GREEN/BLACK FUNCTION +12VDC IGNITION POWER +12VDC BATTERY POWER TO CHASSIS GROUND LEFT (A) SPEAKER (+) LEFT (A) SPEAKER (-) RIGHT (A) SPEAKER (+) RIGHT (A) SPEAKER (-) LEFT (B) SPEAKER (+) LEFT (B) SPEAKER (-) RIGHT (B) SPEAKER (+) RIGHT (B) SPEAKER (-) NOTES: - Speakers must have a minimum of four impedance each. Both do not have to be hooked up at the same time. [. . . ] Push either of the Seek buttons (1 or 2) to tune to the next higher or lower active station. 5) Adjust Volume Control (17) to suit taste. CASSETTE TAPE PLAYER 1) Turn power on by pushing the Power Switch/Volume Control button (17). 2) Use the Source Selectors (18), to select the TAPE button. 3) Use the Speaker Selector Switch (13) to choose between speaker output, headphones, or both. 4) Press the Cassette Eject button (12) to eject any cassettes that may already be in the player. 5) Insert a cassette into the Cassette Player (11). 6) The cassette will automatically play when inserted. 7) You may rewind or fast forward the cassette using the REW or F. F. 8) To change sides of the cassette, press the REW and F. F. 9) To eject the cassette, press the Cassette Eject button (12). 3 AUXILIARY INPUT 1) Push Power Switch (17) "on". 2) Using the Source Selectors (18), choose the button labeled "AUX". CD shuttle) connected to the Auxiliary In Jacks (21) on the rear of the radio, then you can listen to your external source through the system. 4) An external auxiliary source can also be used (such as a portable cassette player) through the 1/8" Auxiliary Stereo Input Jack (14) on the front of the radio. SETTING THE CLOCK 1) Push the Power Switch (17) "on". 3) Use the H and M buttons (1 and 2) to adjust hours and minutes. Note: The T/ F also toggles between time and radio frequency on the display. SETTING STATIONS INTO MEMORY PRESET 1) This unit has the ability to set 18 FM and 12 AM stations into memory. 2) To set the AM or FM stations into memory, first tune to the desired station. [. . . ] The unit will stop at each pre-set station for approx. 5 seconds before continuing on to the next pre-set station Press this button again momentarily to stop pre-set scan operation and remain on the selected station. 2) Pressing this button for longer than 2 seconds will activate the Auto-store Tuning feature which will automatically scan the band and enter up to 6 strong stations into the 6 pre-set memories (the indication "AST" will flash on the display to show that Auto-store Tuning is in progress). After entering the stations into the memories, the unit will automatically stop at each station for approx. [. . . ]