User manual AUDIOVOX AXT847

[. . . ] MODEL : AXT847 MODÈLE : AXT847 Bilingual English / French 17 Minutes Digital Answering Machine Répondeur numérique de 17 minutes BEFORE OPERATING THIS PRODUCT, PLEASE READ THESE INSTRUCTIONS CAREFULLY AVANT DE FAIRE FONCTIONNER CET APPAREIL VEUILLEZ LIRE SOIGNEUSEMENT LES INSTRUCTIONS *Requires AC-AC 9V ADAPTOR & 9V "1604" batteries (not included) *Nécessite un ADAPTATEUR AC-AC 9V et des piles 9V «1604» (non compris) 1 Safety instruction IMPORTANT SAFETYINSTRUCTIONS When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electrical shock and injury to persons, including the following: 1. Follow all warnings and instructions marked on the product. Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. [. . . ] Open the battery compartment cover (located underneath the unit). Insert a 9V (1604) alkaline or carbon-zinc battery, (not supplied) observing the polarity as indicated on the base of the compartment. Important>>During power failure the 9V (1604) alkaline or carbon-zinc battery maintains your Out Going Message (OGM), and any recorded messages, and your Security Code. The unit will not operate until mains power is restored. Note>> If you do not install a 9V (1604) alkaline or carbon-zinc battery, any disruption to the mains power supply will result in a loss of your OGM announcement, any recorded messages, and your Security Code. The OGM announcement and Security Code will revert to the factory default 5 settings. Connecting the Power Ada ptor Only use an adapter with "Class 2 "power source 9V 200mA Insert the plug of the power adapter into the Jack at the back of the answering unit and connect the adaptor to the mains power supply. ANSWER ON-OFF / STOP Button will turn to ON and lighted, if not, please press the Button to turn ON and lighed. The unit will have a sound and the Display(15)will flash "00"and "--" repeats this sequence until the clock and OGM has been set. Note>> If the battery is installed incorrectly or exhausted, then "bL" is added to the display. If you do not want to be disturbed by incoming calls whilst you are setting up the unit, it may be desirable at this stage to set the Clock Day / Time stamp and your own Out Going Message (OGM) before following the connection procedure Connecting to the Telephone Line 1. Plug one end of the TELEPHONE LINE CORD into the jack at the back of the answering system marked TO TEL. Plug the other end of the TELEPHONE LINE CORD into a modular telephone wall jack. You may have to disconnect your existing telephone to do this. Connecting your Telephone Plug the line cord from your existing telephone into the jack at the back of your answering system marked TO TEL. MACHINE RESET CAUTION :IF you press machine RESET, unplug the unit from the telephone line and power adaptor If the system does not record messages or otherwise malfunctions, press the machine RESET button on the bottom near the battery door of the base, pointed instrument such as a pencil. CAUTION : When you press machine RESET, the time / Security code setting and any messages stored in memory are deleted even if a battery is installed. ??ANSWERING SYSTEM SET UP Bilingual English / French Setting Slide the ENG / FRE switch on bottom of the units to select for day and time stamp in English or French. To record or change OGM for ANSWER-RECORD mode It is important that you record your Outgoing Message (OGM) before operating the answering system. Try to keep your announcement brief (under 30 seconds) as this maximizes the recording time available for incoming messages. Press and hold the OGM button, the Displays will show `Ar' and you will hear a long beep 2. Still hold the button and start recording your OGM announcement speaking clearly towards the microphone (16) from approxim ately 6 - 8 inches. [. . . ] The unit comes with a factory default Security Code of 268 which can be changed to any 3 digits ranging from 000 to 999. Press and hold the REPEAT button, after the "beep", the displays shown the code and announcing e. g. Release the button and the display scrolls the current code set after each digit. Press " SKIP" or "REPEAT" button to increment or decrement the digit. [. . . ]