User manual AUDIOVOX DBS-4500

[. . . ] B The DBS-4500 / Land Version In-Motion Satellite Television System Installation Instructions Includes: ­ 100 Series Antennas All rights reserved, patent pending Copyright ?A subsidiary of Datron Systems Incorporated M-01334, Rev. B Page 13 TABLE OF CONTENTS 1. WELCOME. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 1. 1 Satellite Receiver Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 2. INSTALLATION OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Place the antenna system over the mounting holes that were just drilled Re-install spacers and shims and check that the system is still level, if not, readjust shims. Install the eight (8) lag screws and/or installer supplied rivets. Longer lag screws may be required if substantial shimming is needed for leveling. The lag screws should penetrate approximately 3/4". (See Figure 4-4. ) Step 4 Step 5 Step 6 Step 7 Step 8 Step 9 Figure 4-4 Step 10 Check that the antenna is still level, adjust if necessary. CAUTION: MAKE SURE THAT RADOME BASE HAS NOT BEEN TORQUED OR DEFORMED BY THE INSTALLATION TO THE VEHICLE. IF THE RADOME BASE IS DEFORMED, OPERATION OF THE ANTENNA PEDESTAL WILL BE ADVERSELY AFFECTED. M-01334, Rev. B Page 20 Step 11 Apply more sealant at each bolt and/or rivet head to prevent leakage through the mounting holes (See Figure 4-5). Figure 4-5 Step 12 After the hardware has been tightened, generously weatherproof the hardware and penetration points with sealant. Do not attempt to seal around the entire radome base. Cut and remove the shipping tie that locks the antenna in place for shipping (see Figure 4-6). Failure to remove this tie may result in damage to the antenna motors and drive electronics. Step 13 Figure 4-6 M-01334, Rev. B Page 21 4. 2 Connecting the Cables Figure 4-7. Cable Diagram Step 1 Attach the Antenna Control cable circular connector to the antenna. Be sure to rotate the plug clockwise until the connector is completely seated. Connect the two RF cables, RF1 and RF2 and slide weather bolt over the connections. IN SINGLE COAX INSTALLATIONS USE J3 NOT J2. FAILURE TO DO SO WILL RESULT IN ERROR MESSAGE "CODE 10: LNBFV" ON SCREEN. Step 2 Route the RF coax cable and the antenna control cable down through the roof to the receiver. A 3/4-inch hole must be drilled in order to pass the cables down through the roof. M-01334, Rev. B Page 22 Step 3 After the cables are routed, pot the cables with silicone sealant, around the hole. It is not necessary to tin the bare wire leads. The gray "Wago" connector has two mounting ears and may be mounted in any location that is convenient. Make sure the connection is on the wire and not on the wire insulation. Cut off the silver colored shield wire, it is not used. Wiring Aid Tool M-01334, Rev. [. . . ] Possible Solution Contact nearest Authorized Service Center or call Datron at (800) 287-5052 ?Repair or replace coax Check receiver voltage to LNBF CODE: 10 LNBFV Failure of the R-hand/L-hand polarity of the LNBF. M-01334, Rev. B Page 31 6. Warranty Datron/Transco Inc. (DTi) warrants this product to be free from defects in material and workmanship for two (2) years' parts and one (1) year labor. [. . . ]