User manual AUDIOVOX FPE3206

[. . . ] These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications if this equipment does cause or receive interference, which can be determined by turning equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: Reorient or relocate the TV antenna Increase the separation between TV and other equipment Connect TV into separate outlet from equipment Consult the dealer or an experienced raido/TV technician for help FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. 0 0 Safety Cautions 2 Safety Cautions Users are advised to read this user's guide before operating the product. Do not step over or place objects on the electrical cord. Do not over load your electrical outlet. For safety reasons, do not touch any part of the TV , electrical cord, TV antenna or cable during bad weather and thunderstorms. To avoid short circuit, electrical shock or fire; keep this product indoors and away from rain and other forms of liquid. Be sure that the AC plug is disconnected from the outlet before performing any kind of maintenance. When cleaning the TV, do not use liquid chemical cleaners or water sprays. [. . . ] Action 1, Press "MENU" Action 2, Press " CH " ( / ) Action 3, Press " VOL "(-/+) When you have finished adjusting your selections, simply press the "MENU "button to exit. 0 1 Volume Settings 6 Volume Settings Volume Setting (1) 1. Press "Audio" on the remote the select 5 different preset levels of volume. 2. Press "Audio "button; the 5 different levels of sounds will appear as shown. - Standard: High and low are equal - High low pitched - Low pitched - High pitched - Low high pitched Volume Setting (2) 1. You can adjust the "Balance" of the speakers. 2. Simply go to "MENU " setting, locate the "Balance " , and press "VOL" (-/+), and perform the desired adjustment Volume Setting (3) Before you adjust the TREBLE or BASS, please set the Audio Mode (USER), then locate the TREBLE or BASS controls, and perform the desired adjustment. 0 1 7 TV Setting Multichannel Television Sound (MTS) Your TV set is equipped with MTS (Multichannel Television Sound) decoding. This means you can view your programs in the original sound track. (SAP, Second Audio Program). 1. Simply press the "MTS" button to adjust the desired language heard. 2. You may also select "MENU" to do the necessary adjustments step by step. Simply press the select and setting buttons to finalize your selection. 3. When you change a channel selection , or if there is a break in electrical circuit, the TV screen will show your present status as being "Stereo" and/ or "MTS" function, depending on the present status. 4. Yellow lettering on TV settings describes the TV's present status. : Present program has two language settings broadcasting under mono-tone. 5. Weak antenna reception may result in poor Stereo Sound effects. You may also directly input the channel you wish to delete. Press "SKIP ON/OFF" to delete the channel you wish. This action will delete the channnel from your TV. The deleted channel lettering will also change color from green to red. Red TV Setting CHANNEL MEMORY (Enable Channel) If you wish to replace a channel, proceed as follows: 1. From your remote, press "CH"( / ) up or down to locate the channel you want. You may also directly input the channel number you wish to add. Press "SKIP ON/OFF" to add the channel you want. The newly added channel lettering will change from that of red to green. The above enable /disable channel action may also be carried out via the menu button. From Menu, select, then set the channel you wish to add or delete. [. . . ] If they are okay, problem is just with the TV program you are viewing Press the TV/VIDEO/PC button on the remote or on the top of the unit to get to the desired display option If you are using outdoor antenna, please check your connections Please check if your power cord is connected properly, it may be loose Switch off main power, disconnect cable. Reconnect cable after two minutes rest then switch on the main power Check if the antenna or cable are well connected Check your Remote Control Check power adapter and power cord if they have been damaged Connect cable to another TV If all fails, please contact with serviceman immediately 0 2 9 0 3 Troubleshooting 0 Troubleshooting Picture too dark Check your brightness level Check your contrast level In the on screen display (OSD) select default Check your LCD monitor for possible demage Remote Control Failure Check TV main power source Check if remote control batteries are weak Check if batteries have been correctly installed Check if there are obstructions between your remote control and the main TV remote sensor Disconnect your cable for two minutes before reinstalling it If failure resulted from electrical interferences, lighting or static, disconnect the TV main powerfor 10 seconds before reinstalling it. Restart your TV Try holding remote 2 inches from sensor Picture is blurry Check other channels. Problem may be an isolated incidence If using outdoor antenna, please check connections Please check your accessories. [. . . ]