User manual AUDIOVOX LCM1331FDW

[. . . ] A cable tie will mount through holes provided in PCB, and is recommended for wire strain relief. A second component harness is needed to utilize both mini-din connectors. Right Audio In: Use to hook-up Game/Camcorder or DVD (red female RCA jack) Left Audio In: Use to hook-up Game/Camcorder or DVD (white female RCA jack) Video In: From Game/Camcorder or DVD (yellow female RCA jack) Mounting location: Panel mounting locations Headphone Out: Additional headphone out jacks for wired headphones. 3 Front Button Panel Features 1 2 3 4 5 6 7 8 9 1) Power: This button turns LCM1331FD/LCM1331FDW on and off. 2) Channel : Pressing will select higher programmed channels and pressing will select lower programmed channels than current channel. [. . . ] 6) Route the wiring harnesses throughout the vehicle as necessary. (Refer to the wiring diagram on pages 5 and 6 of this manual as well as the wiring instructions for the individual components and accessory options being installed). Be sure that all wiring is protected from sharp edges and is routed in such a manner that it will not be pinched when all components and interior trim are fully installed. Be sure to leave enough slack in the wiring at each component to allow working room. 7) Remove all A/V system components from their packaging and place them loosely in the vehicle at their respective locations. 8) Connect all components together (electrically) and verify proper operation of all system functions. NOTE: This is best done both BEFORE and AFTER all components have been permanently mounted. 9) After verifying proper operation of the system, proceed with mounting of each component. 10) When all components are mounted, recheck function of entire system again to ensure that no wiring was pinched or connected improperly during final installation. Notes Connecting to both the Wireless Headphones RF Transmitter and a FM Modulator will require an additional RCA Adapter (P/N 0892165). One dual RCA Patch Cord is needed to connect the TV/Monitor to the Wireless Headphone RF Transmitter. One dual RCA Patch Cord is needed to connect the TV/Monitor to the FM Modulator, and is included in the FM Modulator package (P/N 0190730). For audio output, there are a few scenarios that may apply to your system: a) Remote headphone jacks may be added and located throughout the vehicle. b) Additional speakers and amplifiers may be added throughout the vehicle. 5 Vehicle Preparation 1) Locate vehicle power source. Generally this is best found near the vehicle's fuse block, which is usually (though not always) under the steering wheel area. Locate an accessory hot circuit to tap into video system power. Accessory hot means a circuit that is +12VDC when the ignition key is in either the "ACC'Y" or "Run" positions, and 0 volts DC when the ignition key is removed from the vehicle. 2) Mounting location and method for the individual components will vary from vehicle to vehicle. This manual will only focus on the installation of the video pod itself and related console accessories. 3) Generally, the best location for the video pod itself is where the vehicle's dome light is traditionally installed (center of roof, just behind the two front seats). The pod should NEVER be located in a position that would place it within the driver's field of view. [. . . ] 12) VCP Power: Toggles VCP power on/off 17 16 13) Play: Play tape in VCP 14) REW: Rewind tape in VCP 15) FFWD: Fast forward tape in the VCP 15 12 14 16) Replay: this button will stop current play, rewind the tape and replay the tape from the beginning 17) Stop: Stop the tape in the VCP. 9 Cut-Away View of Mounting Bosses Roof Structure Screw Boss C3 Note: If longer screws are substituted, care should be taken to prevent piercing the roof, and be sure that pan head screws and washers are used to prevent screws from pulling through the screw boss. Eight screws must be used and secured to solid structure when mounting. Antenna Information The following are a few points to consider in regards to TV reception in a mobile application. Generally in a mobile application, the lower channels are the most difficult to receive due to the size of the antenna needed to receive the signal. When the antennas are inside the vehicle, the TV signal can be obstructed by the outside metal of the vehicle. [. . . ]