User manual AUDIOVOX LCM641TVB INSTALLATION

[. . . ] C ­ Mounting Screw Bosses Use these to secure the unit to the roof structure of the vehicle and/or console assembly (optional) Figure 1 General Installation Approach: 1) Before beginning installation, please refer to warning on manual page 10. 2) Decide upon system configuration and options that will be installed (ie: what components, VCP, Tuner, Remote Headphones, 2ND VCP, etc. ) 3) Review all manuals to become familiar with electrical requirements and hookups. 4) Decide upon mounting locations of all components and method of mounting. 5) Prep the vehicle by removing any interior trim necessary to gain access to vehicle power hook-up point as well as all areas where interconnecting wire harnesses will need to be located. [. . . ] Locate an accessory hot circuit to tap into for video system power. Accessory hot means a circuit that is +12VDC when the ignition key is in either the " ACC' or " Y" Run"positions, and 0 Volts DC when the ignition key is removed from the vehicle. 2) Mounting location and method for the individual components will vary from vehicle to vehicle, so this manual will only focus on the installation of the video pod itself and related console accessories. 3) Generally, the best location for the video pod is where the vehicle' dome s light is traditionally installed (center of roof, just behind the front 2 seats). The pod should be located in such a manner that it can be comfortably viewed by the rear seat passengers in the vehicle. The pod should NEVER be located in a position that would place it in within the driver' field of view. This is not s only hazardous for driving conditions (as it creates a distraction to the driver), but it is against the law in many states. 4) Once pod location has been determined, there may be prep work required for the headliner. Some of the steps that may need to be taken depending upon your installation are: a) Removing of the vehicle' dome light. s b) The headliner MAY have to be cut out per the diagram below. ** c) If the mini-console is being used, it will have to be trimmed to fit the contour of the headliner. Note, steps a-c above are not required for all installations. . . you may have to do none, some, or all of these steps. ** IF your particular installation will require you to cut out the headliner, the box that this kit came in can be used as a template. You can remove the shelf that the video pod rests upon and trace the opening onto the headliner for cutting. Figure 2 Page 5 of 11 P/N 8010845 Rev. F Nov. 00 Wiring Diagram Hook Up Procedure: Figure 3 1) Insert the circular mini-din connector of the source component harness through wire tie loop on the main PCB and into mini-din connector on main PCB (fig. 3). 2) Pull wire tie loop tight and cut off excess. 3) Connect power harness to mating connector on video monitor. 4) Connect power harness to vehicle' electrical system s by tapping into an accessory hot line. 5) Verify all functions of system before final mounting of finished assembly. Black: Ground Red: +12 VDC (Accessory Cir. ) TV antenna (If applicable) Mini din connector (Source Component harness) Wire tie Loop Mini-DIN Receptacle Figure 4 Power Harness Item # 3a Power Connector (2-pin) Antenna Connector Optional Remote Headphone Stations Stereo Headphone Jack Spade Terminals Green (Right+) Spade Terminals Black (Ground) A/V Source definitions: 1 = Tuner 2 = VCP (left mini-din on main PCB 3 = 2nd VCP (right mini-dIn on main PCB for game, future DVD, etc. Note: AUX Input overrides 2nd VCP (DIN) Input when connector is plugged into RCA jack Stereo Headphone Jack Spade Terminals Gray (Left+) Page 6 of 11 P/N 8010845 Rev. F Nov. 00 Source Component Harness Hook-Up: Figure 5 A second VCP or other A/V component can be connected to video monitor system using a second source component harness (purchased separately, P/N 8010730). This second harness would plug into second Mini-Din connector on main PCB as in steps 1 and 2 above. Video Out (Yellow) Yellow RCA (Video In) Right Out (Red) Left Out (White) White RCA (Audio In Left) Red RCA (Audio In Right) Source Component Harness P/N 8010730 Power Connector (4-pin) "Y" Adapter for use with Non-Stereo Installations P/N 0892165 IR LED: Clean the IR Receiver Window on the front of the VCP. Remove Adhesive Backing and Apply IR LED to IR Window on the Face of the VCP. VCP (Rear View) Page 7 of 11 P/N 8010845 Rev. F Nov. [. . . ] d) Check fit of trimmed console and make any minor adjustments necessary. 4) The mini console can be painted or covered with a material that matches headliner before assembling mini console to the video pod. 5) The finished mini console should be attached to video pod, then attach assembly to roof. See figure 7. Headliner Cut Line Lowest Point Mark Page 8 of 11 P/N 8010845 Rev. F Nov. [. . . ]