User manual AUDIOVOX OD70 P

[. . . ] PROV916/ VOD705 AUTO PROG CHANNEL SOURCE ON OFF AUTO VOLUME FM SELECT AP S PROV916 S/ PROV916 P DVD PLAYER WITH DROP-DOWN VIDEO TV/MONITOR HEA DPH ONES I NPU T VI E DO R I AUDI O R L ® ELECTRONICS CORP . 128-6745 DATE : 21/05/03 128-6745 1 of 31 Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a screen that is located in the motor vehicle at any point forward of the back of the driver's seat, or that is visible, directly or indirectly, to the driver while operating the vehicle. In the interest of safety, the PROV916/PROV916 S/PROV916 P should never be installed where it will be visible, directly or indirectly, by the operator of the motor vehicle. Warnings Do not use any solvents or cleaning materials when cleaning the video monitor. Do not use any abrasive cleaners, they may scratch the screen. Use only a lightly dampened lint free cloth to wipe the screen if it is dirty. [. . . ] AV1 Input The video inputs may be connected to a Video cassette Player (VCP), video game system, or other audio / video devices. To access the A/V inputs, turn the PROV916/PROV916 S/PROV916 P on and press the source button on the PROV916/PROV916 S/PROV916 P or the Source button on the remote control until "AV1" is displayed on the screen. Turn the video source component on with its power button or remote control. The PROV916/PROV916 S/ PROV916 P is now ready to play the audio and video signals from the source connected to AV1 input. AUX A/V Input The PROV916/PROV916 S/PROV916 P will accept an audio/video input through the RCA jacks located on the side of the unit. The audio / video device could be a video game system, video camera, or other input device. Video Out The PROV916/PROV916 S/PROV916 P provides a video output for an optional video monitor(s). (Refer to page 6 of the Installation Guide for more details. ) This output will provide a video signal that duplicates the signal displayed by the PROV916/PROV916 S/PROV916 P to an additional monitor or video display. Please see your installer for more information. -16- 128-6745 16 of 31 DVD Basics To get the optimum use out of the DVD section, make sure you read this section completely. Regional Coding Both the DVD player and disc are coded by region. These regional codes must match in order for the disc to play. If the codes don't match, the disc won't play. Other regional codes cannot be played in this unit. The unit will display "WRONG REGION. " Types of Discs your DVD will play · DVD discs ­ DVD discs which contain video. · Audio discs ­ Audio CDs contain musical or sound content only. · MP3 discs ­ A disc that contains audio files (for example, a CD-R with downloaded MP3 files). · VCD discs ­VCD discs which contain video. Loading and Playing Discs Before you load a disc, make sure that it is compatible with the player. Note: the following Discs CANNOT be used with this player : · MiniDisc · · Laserdisc CD-I, CD-ROM, DVD-ROM To load and Play a Disc Press the Power button to turn the unit ON. Select DVD mode and insert the disc (Label Up) into the disc compartment. -17- 128-6745 17 of 31 Settings and Adjustments This chapter describes how to set and how to adjust using the on-screen SETUP menu. Using the Setup Menu Using the setup display, you can do the initial setup, adjust the picture quality, and set the various outputs. You can also set a language for the on-screen display and the setup display and limit playback by children. 1) Press the SETUP button to display the "setup menu" on the display screen. 2) Select the main item you want using the cursor (ML) buttons, and then press the ENTER button. [. . . ] If the regional codes don't match, the disc can't be played. Allow player to dry out. The icon ( appears on screen ) Play starts, but then stops immediately The feature or action cannot be completed at this time because: 1. The disc's software doesn't support the feature (e. g. , angles) 3. The feature is not available at the moment. [. . . ]