User manual AUDIOVOX RVMPKG2 INSTALLATION

[. . . ] 9 SW1, SW2 and SW 3: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Then fasten the other belt on the other side of the mirror. To prevent the RVMPG2 from falling off, tighten the belts until secure to the factory rearview mirror on both sides. 5 Figure 3 e) Cut off the excess part of the 7-inch strap (2) Plug the Mitsumi connector from the Audiovox navigation monitor cable (part #112C3080) into the receptacle at the top backside of the mirror/monitor screen. Route the rest of the monitor cable to the Navigation computer. (3) Connect the control box monitor cable to the rearview mirror/monitor cable. Route the monitor cable behind the headliner of the windshield then down the A pillar behind the plastic shroud to the under dash area. (4) Connect the 5 wires in the following manner. a) Red wire - 12 volt constant (positive) b) Black wire - Chassis ground (negative) c) Blue wire - 12-volt ignition (12 volt with ignition on) d) Green wire - Reverse light switch (12 volt when vehicle is in reverse) e) Yellow wire ­ Parking brake light switch (Negative when parking brake on) WARNING: Observed polarity when connecting the cables. The cable must not be reversed or modified. Select a suitable and convenient location for the mobile phone. Install the mobile phone hands free seat (1) 6 (2) Tear off the adhesive tape on the back of the hands free seat. Press tightly to seat on to the selected surface for 30 seconds till the two surfaces are tightly glued. NOTE: Make sure the two surfaces are glued tightly! (3) Clean a place on the back of the cell phone, keeping it dry. Remove the adhesive tape of the rounded metal sheet and stick it to the selected place on the back of the cell phone. NOTE: Do not attempt to move the phone within 24 hours after gluing. CAUTION: The rounded metal sheet can only be glued once, so be sure it is at the right place! Figure 4 7 3. Signal Inputs The signal input connections for the system include: (1) Rear Camera: By connecting rear camera with control box plug, users can see the rearview when the vehicle is in reverse. (2) Hands Free Jack: Put the hands free plug (3. 5mm) into hands free jack and put the other side of plug into the headphone jack of the mobile phone. (If necessary, find a compatible adapter). (3) Navigation: The navigation signal is supplied via the connector plugged directly into the rear of the mirror. (4) Video In, Video Out, Audio In, Audio Out, Audio/Video Input and Output Plugs (3. 5mm) are located in the control box. [. . . ] Check for 12 volts on the blue wire while Ign on. Check the LCD Contrast (Brightness) control knob whether the contrast knob is set too low. Check the rearview Camera wiring and connection. Check the cable from the rearview mirror is connected to the control box. [. . . ]