User manual AUDIOVOX SRS1000

[. . . ] * TV/Radio mode is activated via a simple 12VDC trigger line, which can be controlled by your own switch (integrated into your dash design, for example). * 3 band EQ (100Hz, 1KHz, 10KHz centers), +/_ 10dB boost/cut for each band. * TV and Radio gain controls to match the system to your devices for optimum performance. * 3D field adjustment, to match size of sound field to vehicle. [. . . ] Wire Harness - 8 pin - Radio High Level (Speaker Input ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1pc R THEATER SOUND SRS1000 4. Owner's manual. . . . . . . . . . . . . . . . . . . . . . . . . . . 1pc ----- 1 ----- TH E UA z LIZ ER 10k Hz SRS1000 Theater Sound Owner's Manual Owner's Manual SOU ND SR S1 00 0 SRS1000 Theater Sound Owner's Manual Front/Rear Panel Description (1) Front panel view Radio Gain TV Gain 3D-Field 3-BAND EQUALIZER TV Radio 100Hz 1kHz 10kHz Min Max Min Max Min Max Min Max Min Max Min Max Front panel description: 1. Radio gain control---Adjust gain to match Radio signal level. TV gain control---Adjust gain to match TV signal level 3. TV indicator ---Illuminated Orange LED when unit is in TV mode. Radio indicator---Illuminated Green LED will unit is in Radio mode. 100 Hz Band Adjustment---Adjust low frequency response (Bass) of the amplifier when in TV mode . This control has no effect on radio mode. 1 kHz Band Adjustment---Adjust middle frequency response (Midrange) of the amplifier when in TV mode . This control has no effect on radio mode. 10 kHz Band Adjustment---Adjust high frequency response (Treble) of the amplifier when in TV mode . This control has no effect on radio mode. ----- 2 ----- SRS1000 Theater Sound Owner's Manual Front/Rear Panel Description (2) Rear panel view RR LR RF LF + _ Hi Level In TV In Hi Level Line In TV Radio SW1 RR RF Trigger SW2 LR LF DC + _ R Speaker Out Made in China L R L is a trademark of SRS Labs, Inc. Rear panel description: 1. Using the included 8 pin wire harness, connect the speaker output of the radio to SRS1000. Do not use this input simultaneously with Radio Line In. TV In, High Level -- This input is to be used only with monaural TV's (non-stereo) that do not have variable, stereo, line level out put. If this input is used, no connection should be made to Line In, TV. Doing so would cancel the SRS 3D effect. 3. Line in, TV--Connect to Stereo TV variable line level out put . Do not connect any cable to the TV In , Hi Level Jack if this input is used . 4. Line in , Radio--Connect to variable line output from radio (if available). Do not connect the 8 pin harness to the SRS1000 if this input is used. Use included 16 pin wire harness to apply power, TV mode trigger, and all speaker outputs though this connection. Refer to page 4 for details. ----- 3 ----- SRS1000 Theater Sound Owner's Manual System Connections (2) Note: Be sure that left & right speaker channels are connected properly from TV, Radio, and to speakers. [. . . ] This control is to compensate for the acoustic properties of small and large vehicles, which are very different. As a gengeral rule of thumb, the smaller the vehicle, the more 3D effect is needed to simulate the full "theater experience". For the most part, however, this adjustment is mostly according to personal taste. ----- 6 ----- SRS1000 Theater Sound Owner's Manual Specifications: 1. rating) : Front channel : 15w+15w (4 ) Rear channel : 15w+15w (4 ) Subwoofer channel : 25w+25w (4 ) 2. [. . . ]