User manual AUDIOVOX VOH682A INSTALLATION GUIDE

[. . . ] Be sure that all wiring is protected from sharp edges and is routed in such a manner that it will not be pinched when all components and interior trim are fully installed. Be sure to leave enough slack in the wiring at each component to allow working room. 6) Remove all A/V system components from their packaging and place them loosely in the vehicle at their respective locations. 7) Connect all components together (electrically) and verify proper operation of all system functions. [. . . ] An alternate method is to use a piece of plywood (5"x9"x3/4"). First secure the plywood block to the crossmember, then screw the monitor into the plywood. It is best to mount the video monitor to the roof structure without the mini console first. There should be a gap between the headliner and the outer flange of the video monitor. The mini console should be cut to full this gap. Apply masking tape to the outer surface of the mini console in the areas where the cut will be made. Mark the cut to follow the necessary contour of the roof. The suggested method of marking is as follows: A) First mark the narrowest point of the mini console on the masking tape. Be careful to consider not only vertical location, but fore-aft location. B) Using the handle of a screwdriver, make a "transfer marking tool" See diagram below. Place the tool against the roof, and the marker against the masking tape on the mini console. Trace the cut to be made around the entire perimeter of the mini console. C) Cut the mini console using a sharp utility knife or shears. Make the cut in several passes over the marked line, each time cutting a little deeper. It is not necessary to cut completely through the plastic, the cut only need be over 50% of the wall thickness of the plastic. By bending the cut back and forth several times, the plastic will break cleanly at the cut. D) Check the fit of the trimmed console and make any minor adjustments necessary. The mini console can be painted or covered with a material that matches the headliner before assembling the mini console to video monitor. The finished mini console should be attached to the video monitor, then attach the assembly to the roof. 2) 3) 4) 5) Headliner Cut Line Lowest Point Mark Figure 6 Tape marker to screwdriver starting at your mark for the lowest point, then trace the contour of the roof Headliner Cut line Lowest point mark Refer to Fig 7 for detail on attaching console to video mark Tape marker to screwdriver. Starting at yourpod and video pod to vehicle structure. for the lowest point, trace the contour of the roof -4- MOUNTING THE MINI CONSOLE Roof Roof support Headliner 5"x9"x3/4" Plywood Block or Optional VOHBKT (4) #8x1" self drilling screws (not supplied) Mini-Console Video unit (4) #8 Flat washers (not supplied) (4) #8x3/4" self tapping screws (not supplied) -5- VOH681A Note: cables exiting the pod should be routed as shown. Wireless FM Modulator Antenna Red: +12 VDC (Accessory Cir. ) Black: Ground Optional Hard Wired FM Modulator Output 2 12 VDC Power and Ground 1 Left Input RCA-Female LEFT WHITE RIGHT RED RCA-Female Accessory Harness Item# 2 Accessory Harness Item# 2 1 Power Harness 4 Item # 3a choke Mini-Din Connectors TO FACTORY RADIO Am/Fm Antenna Dash Radio FM Modulator 1070610 Right *Refer to Instructions with the RF Input Modulator Kit for further details. Patch Cord To Secondary AV Monitor TO OPTIONAL ADDITIONAL MOINTOR 12 VDC Power and Ground INPUT VIDEO RCA-Female LINE OUT VIDEO Auxillary video display Patch Cord RCA Male to Male Red RCA (Audio Right) White RCA (Audio Left) Yellow RCA (Video) Optional Remote Headphone Stations Stereo Headphone Jack Stereo Headphone Jack IR LED: Clean the IR Receiver Window on the front of the VCP. Remove Adhesive Backing and Apply IR LED to IR Window on the Face of the VCP. [. . . ] Verify connections at both ends of the source component harness. -Push and hold the volume up button until sound is heard over headphones. If problem is limited to the dash radio, verify radio is tuned to the correct channel, and that power to the wired RF modulator is on. (Refer to instructions with modulator kit). [. . . ]