User manual AUSTRALIAN MONITOR SYNERGY2 BROCHURE

[. . . ] SYNERGY SERIES 2 Two Channel Power Amplifiers Drawing on the heritage of Australian Monitor's low impedance amplifier design comes the latest in low impedance amplifiers from the Australian Monitor Pro series, the Synergy2. [. . . ] All models also offer on board clip limiting, ground lift switching, XLR ins and binding post and 4 pole speaker connector outputs. As with all Australian Monitor Pro Series amplifiers they deliver the sonic clarity you've come to expect from an AM amp. At a Glance > 3 models > All 2 ohm capable > SY2200 2 x 110W into 8 ohm, 2 x 200W into 4 ohm, 2 x 300W into 2 ohm > SY2400 2 x 190W into 8 ohm, 2 x 350W into 4 ohm, 2 x 525W into 2 ohm > SY2700 2 x 400W into 8 ohm, 2 x 700W into 4 ohm, 2 x 1000W into 2 ohm > On board clip limiter > Ground lift switch > XLR in and link (male/female) > Binding post/4 pole speaker connector outs SYNERGY2SERIES Architectural Specifications The amplifier shall be of 2 channel low impedance design, of sturdy construction and shall be 2 rack units high. The amplifier shall have on board clip limiting, ground lift switching, XLR inputs and 4 pole speaker connector and binding post outputs. Front panel level controls will be provided as well as status, overload, thermal, power and fault indication. The amplifier will be capable of 2 ohm operation and shall have overload, output short circuit, thermal and output DC protection as well as a slow start facility. The amplifier shall be an Australian Monitor Synergy2 series. [. . . ] Common Specifications (To all SY2 Amplifiers) Distortion (re: 4ohm, 1dB below clip) THD (@ 1kHz) <0. 02% IMD SMPTE (60Hz : 7kHz 4:1) <0. 03% 20kohms 1Vrms >80dB A-Weighted >104dB >70dB >40 V/µsec (@ 1kHz re 8 ohms) > 375:1 (+/-3dB) 15 Hz- 50 kHz Power, Status (L/R), Overload, Thermal, Fault Input Impedance Input Sensitivity Input CMRR Signal/Noise Ratio Crosstalk Slew rate Damping factor Frequency response Indicators Model Output Power Voltage Gain Thermal Dissipation SY 2200 300W 0. 1% THD @ 1kHz 28. 3 (29dB) Both channels driven, 2ohm load 1/8th power 425W (1450btu/hr) SY 2400 525W 0. 1% THD @ 1kHz 37. 4 (31dB) Both channels driven, 2ohm load 1/8th power 780W (2661btu/hr) Both channels driven, 2ohm load, 230Vac 1/8th power 5. 0A 87mm x 482mm x 400mm 15. 5kg 17 Kg 210mm x 540mm x 540mm SY 2700 1000W 0. 1% THD @ 1kHz 52. 9 (34dB) Both channels driven, 2ohm load 1/8th power 1410W (4811btu/hr) Both channels driven, 2ohm load, 230Vac 1/8th power 9. 1A 87mm x 482mm x 455mm 17. 5kg 19 Kg 210mm x 540mm x 575mm Current Draw Both channels driven, 2ohm load, 230Vac 1/8th power 2. 7A Dimensions (H x W x D) Unit Weight Shipping Weight Shipping Dimensions (H x W x D) 87mm x 482mm x 400mm 12. 5kg 14 Kg 210mm x 540mm x 540mm ENGINEERED AND DISTRIBUTED BY AUSTRALIAN MONITOR ABN 78 001 345 482 149 Beaconsfield Street, Silverwater Sydney NSW 2128 Australia NSW Tel: (02) 9647 1411 Fax: (02) 9648 3698 VIC QLD SA WA NZ Tel: (03) 9890 7477 Fax: (03) 9890 7977 Tel: (07) 3852 1312 Fax: (07) 3252 1237 Tel: (08) 8352 4444 Fax: (08) 8352 4488 Tel: (08) 9204 0200 Fax: (08) 9244 3783 Tel: (09) 415 9426 Fax: (09) 415 9864 [. . . ]