User manual AVANTI WDP69 INSTRUCTION MANUAL

[. . . ] MANUAL DE INSTRUCCIONES / INSTRUCTION MANUAL DISPENSADOR DE AGUA FRIA Y CALIENTE / WATER DISPENSER Número de Modelo / Model Number: WDP69 PRECAUCION: ANTES DE USARSE, LEA ESTAS INSTRUCCIONES Y SIGA LAS REGLAS DE SEGURIDAD. La sección en español empieza en la página 12. Avanti has a policy of continuous improvement on its products and reserves the right to change materials and specifications without notice. La política de Avanti es la de tener mejoras continuas en sus productos y se reserva el derecho de cambiar los materiales y especificaciones sin notificación alguna. Avanti Products P. O. Box 520604 - Miami, Florida 33152 www. avantiproducts. com 1 Table of Contents Help Us Help You ____________________________________________________ 3 Parts An d Features ___________________________________________________ 4 Important Safety Instructions___________________________________________ 5 Installation Guidelines ________________________________________________ 5 Before Using Your Water Dispenser ____________________________________ 5 Operating Your Water Dispenser _______________________________________ 6 Care And Maintenance ________________________________________________ 7 Taking The Dispenser Out Of Service ___________________________________ 7 How To Secure Your Unit To The Wall __________________________________ 8 Troubleshooting Guide _______________________________________________ 9 Your Avanti Products Warranty________________________________________ 10 Wiring Diagram______________________________________________________ 11 Spanish Section 12-15 2 IF YOU NEED SERVICE We're proud of our service and want you to be pleased. [. . . ] Hot Water Control Turn heating switch (12) on, the red indicator (2) will be lit and the unit will begin to heat the water. When 6 When the water reaches the right temperature the red light goes off automatically. When the temperature goes down to approx. 80º C (176º F), the red indicator will glow again and another heating process starts. NOTE: THE HOT WATER FAUCET HAS A CHILD-SAFETY GUARD ATTACHMENT. Continue holding safety button while pushing in faucet as long as water is being dispensed. When faucet is released, make sure to return it to the original position. ?Cup Dispenser (Optional) A cup dispenser may be installed by using the mounting holes (covered with plastic caps) located near the top of the right side panel of the cooler. The cup dispenser comes equipped with a mounting bracket and screws and may be ordered by completing the enclosed order form provided with your instruction manual. CARE AND MAINTENANCE ?Wash the inside of the reservoir with a warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda to a quart of water. The drip tray and water faucets should be cleaned with mild detergent and warm water. At regular intervals or once a month inspect the coils located across the back of the dispenser. Vacuum accumulation of dust or clean it with a hard brush. TAKING DISPENSER OUT OF SERVICE ?If the water dispenser will not be used for a long period of time, unplug the power cord from the wall outlet. Turn the switch marked "HOT" to the "OFF" position. Drain the water from the tanks by removing the plug from the back of the dispenser. WARNING--THE WATER COMING OUT OF THE BACK SIDE MARKED "HOT" MAY BE SCOLDING. ? Unit should not be transported on the sides. Place it upright if possible and cover it with a blanket. Installation instructions on how to secure your Avanti unit to the wall 7 1- Attach the mounting brackets provided, into the pre-drilled holes located at the back of the unit side panels (see picture 2A) by using the self-tap screws provided. 2- After both brackets are properly installed, use the other end of the bracket to assist in aligning the holes to be drilled on the wall as follows: Measure the center of the bracket mounting hole and the ground (see picture 2A), and measure the distance between the center of both brackets mounting holes (see picture 2B). Both of the above measurements will give you the exact location for drilling the holes on the wall where the unit will be secured. 3- Please be aware that when securing these brackets to the wall, different types of bolts may be used, depending on the different types of wall construction (these bolts are not included). If you are not able to obtain the measurements as explained above, you can also mount and secure both brackets to the unit. [. . . ] CONTROL DE AGUA FRIA: ENCIENDA EL INTERRUPTOR DE AGUA FRIA (13). EL INDICADOR DE LUZ VERDE (4) SE ENCENDERA Y EL PROCESO DE ENFRIAMIENTO COMENZARA. CUANDO LA TEMPERATURA ALCANCE APROXIMADAMENTE 5-7°C LA LUZ VERDE SE APAGARA AUTOMATICAMENTE. ? CONTROL DE AGUA CALIENTE: ENCIENDA EL INTERRUPTOR DE AGUA CALIENTE (12). EL INDICADOR DE LUZ ROJA (2) SE ENCENDERA Y EL PROCESO DE CALENTAMIENTO DEL AGUA COMENZARA. [. . . ]