User manual AVERATEC AVERATEC ALL-IN-ONE

[. . . ] Regulations Information FCC-B Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. [. . . ] If the system is operating abnormally, you can reboot the PC by holding down the power button until the PC turns off. Then press the power button again to boot back up. Case 3 Power saving mode. Saves your session and puts the computer in a lower-power state so that you can quickly resume working. Click Stand By. Chapter 2 Getting Started 6 Adjusting the Brightness of the Monitor You can adjust the brightness by clicking the brightness control button on the front side of the PC. There are 5 levels of LCD brightness adjustment available. Each press of the brightness control button will cycle through each level. Brightness control button (toggle) Using the brightness control button 100% (full brightness level) 60% of brightness level 70% of brightness level 90% of brightness level 80% of brightness level Chapter 2 Getting Started 7 Adjusting the Speaker Volume The Speaker volume level can be adjusted easily with the button located on the Front side of the PC. Speaker Speaker Volume button (Up/Down) To adjust the volume level, press the left volume button to increase the volume level and the Right volume button to decrease the volume level. Mute button To mute the speaker sound, press it once to enable mute and press it again to disable mute. Mute button Volume button (Up/Down) Chapter 2 Getting Started 8 Connecting External Speakers Connecting External Speakers Connect the speakers to headphone jacks Speakers (optional) Audio control panel To set the audio configurations, refer to the follow steps: 1. Double click the Controls IDT Audio Setting icon. Chapter 2 Getting Started 9 2. Set the audio configurations. < Click the Level icon > < Click the Equalizer icon > < Click the Jack Setup icon > 3. Choose which jack (Headphone or Microphone) you have your external speakers connected to. When you finish the setting, click . Adjusting volume The Averatec All-In-One PC has built-in speakers on the base of the system. You can adjust the volume by clicking the volume adjustment buttons located on the front side of the PC and / or by using the volume control feature in Windows XP. Chapter 2 Getting Started 10 Using the Optical Drive The Averatec A1 PC is fitted with a slim-tray-loading optical drive (COMBO or DVD Recorder). Tray-loading CD drive 1. Press the Eject button of the CD/DVD drive. 2. Insert CD/DVD Insert CD/DVD in the CD/DVD drive and place CD/DVD label upside front. Eject CD/DVD Press the Eject button of the CD/DVD drive on the left side of the Averatec A1 PC. You can then remove the CD/DVD. Chapter 2 Getting Started 11 Note  If you can not eject a CD/DVD from the drive, click Start, choose Computer, right-click on the CD/DVD drive that the CD/DVD is in and choose Eject in the popup menu.  If you can not eject a CD/DVD from the drive by pressing the eject button and choosing the Eject menu, insert the paper clip into the emergency eject hole as far as it will go then the tray will be slightly open. Pull out the tray and remove a CD/DVD from the tray. 2 1 3  Make sure CD/DVD is not inserted upside down. (CD label side facing toward upside of PC).  Labels on CD/DVD may cause noise when CD/DVD drive is working. Remove labels on CD/DVD for safe use. Chapter 2 Getting Started 12 Connecting to the Internet 1. Press the power button and the Windows XP start screen will appear. Connect a LAN cable to the LAN connector as shown in the figure below. 2. Configure the communication settings for the system based on your communication environment. When connecting to the Internet via an internet service provider, contact the service provider for more information on required communication settings. Launch Internet Explorer or other communication software. Chapter 2 Getting Started 13 Using Your Webcam You can take photos and chat with your friends. Take photos To take photos, follow the next steps : 1. Double click the CyberLink YouCam icon( ) on the desktop. 2. [. . . ] Before proceeding, make sure that the system is turned off, that you are wearing an anti-static wrist strap (available in most computer shops), and that your workspace is dust and smoke-free. Removing the CD Drive and the system cover Place the system on an open flat surface and remove the screws and back cover as shown in the figure. 1 Make sure that the LCD panel does not get damaged. Chapter 4 Expansion of the system 28 2 To fix the LCD panel, fold it until the latch snap into place as shown in the figure. 1 2 3 Spread the soft thing such as cloth over the flat surface and face down the LCD panel. (Be careful not to damage the LCD panel. ) 4 To firm the system module, insert the flat things (such as the books) between the LCD and system module. 5 To remove the CD drive, insert the flat driver into the hole and slide toward the CD drive and remove it. [. . . ]