User manual AVIOM PB28

[. . . ] A Phillips screwdriver is required to mount the PB28 Series modules to the PB28 Patch Panel. PB28 Modules These modules are currently available for the PB28: · · · · · · 28-XF-DB 28-XM-DB 28-EC-EC 28-XM-XF 28-XF-XM 28-AES-DB XLR female (f ) to DB25 (r) XLR male (f ) to DB25 (r) EtherCon on both sides XLR male (f ) to XLR female (r) XLR female (f ) to XLR male (r) XLR male/female (f ) to DB25 (r) for AES/EBU digital data Assembly The basis of the PB28 system is the PB28 Patch Panel, a blank, 1U-high unit that accepts up to two PB28 Series modules. Secure the optional modules to the PB28 Patch Panel before mounting the product in an equipment rack. To attach a PB28 Series module to the PB28 Patch Panel: 1. [. . . ] It allows Cat-5 network connections from multiple devices to be brought to a convenient central location in any patch bay. The 28-EC-EC module can be used with Aviom A-NetTM products or with any Cat-5 based data system. About the EtherCon Connector The Neutrik EtherCon connector is a dual RJ45 type connector. It can receive a standard Category 5e cable or a cable fitted with the special heavy-duty locking EtherCon connector. When using a standard Cat-5e cable, plug the cable into the center of the jack; release the cable by pressing on the small plastic tab built into the cable connector. Insert an EtherCon equipped cable into the jack until it clicks and locks in place. To remove the cable, press on the metal release tab at the top of the panel-mounted EtherCon jack and pull the connector outward. Tascam/Digidesign AES Pinout Cold 14 15 16 17 18 19 20 21 9, 11 PB28 Modular Patch Bay System DB25 Shell Lift Ground (default) Lift Made in USA The switch on the left side of the module will ground Pin 13 of the DB25. In a standard DB25 audio pinout, for example, this pin is not connected to ground. Digital DB25 Connectors The 28-AES-DB module provides eight channels of AES/EBU digital I/O in stereo pairs, per the AES specification. It is equipped with two DB25 connectors to accommodate the different AES wiring pinouts currently in use by major manufacturers of digital gear. Only one DB25 connector can be used at a time. Tascam/Digidesign Yamaha AES Pinout Hot Gnd 22 10 23 24 12 25 13 13 1 2 3 4 5 6 7 8 Hot Data In (stereo pairs) Cold 12 23 9 20 6 17 3 14 13 Gnd 25 11 22 8 19 5 16 2 Yamaha Caution: Connect only one digital source at a time AES/EBU Digital Data I/O Data In (stereo pairs) The following tables describe the pinout configurations used on the 28-AES-DB module. Data Out (stereo pairs) Data Out (stereo pairs) 24 10 21 7 18 4 15 1 Unused Unused Aviom, Inc. warrants this product against defects in materials and workmanship for a period of one year from the date of the original retail purchase. This warranty does not apply if the equipment has been damaged due to misuse, abuse, accident, or problems with electrical power. The warranty also does not apply if the product has been modified in any way, or if the product serial number has been damaged, modified, or removed. If a defect is discovered, first write or call Aviom, Inc. to obtain a Return Authorization number. No service will be performed on any product returned without prior authorization. will, at its option, repair or replace the product at no charge to you. [. . . ] DOES NOT ACCEPT LIABILITY BEYOND THE REMEDIES SET FORTH IN THIS LIMITED WARRANTY DOCUMENT. AVIOM, INC. 'S LIABILITY IS LIMITED TO THE REPAIR OR REPLACEMENT, AT OUR OPTION, OF ANY DEFECTIVE PRODUCT, AND SHALL IN NO EVENT INCLUDE INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND. SOME STATES DO NOT ALLOW EXCLUSIONS OR LIMITATION OF IMPLIED WARRANTIES OR LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. A-Net and the A-Net icon are trademarks of Aviom, Inc. [. . . ]