User manual AVIOSYS IP POWER 9223K FIRMWARE V1.01

[. . . ] IP Power 9223K User Manual Release Date: 05/26/2010 Manual Version: 1. 0 Firmware:1. 01 - 1Ref#9223K05260001 Warning: Any changes made to this equipment without permission may cause damages to the device! IMPORTANT NOTICE 1. IP Power 9223K was designed to be used with a protective covering, the user is responsible for any damages caused from misuse, or use under inappropriate conditions. Please use the power adapter provided by the dealer, the manufacturer is not responsible for any damage caused from using power adapters not. Do not shake the IP Power 9223K in any fashion 4. [. . . ] Each of the relays on the board has the option to pick whether this circuit will be normally closed (NC) or normally open (NO). Each relay can support a voltage up to 240VAC / 30 Vdc. & a current of up to: N. O . Maximum: 10Amp N. C. Maximum: 5Amp - 9Ref#9223K05260001 Note: Please remember that you use normally open or normally closed the output control will either create a open circuit or a closed circuit. Device Status Normally Closed Normally Open Control Status On On Circuit Open Closed Connecting devices to the 9223K Warning: This part of the procedure can be very dangerous. Please follow instructions carefully or consult an electrician or someone who is experienced in the field to assist in the part of the procedure. Aviosys is not responsible for any damages to the device or harm caused by from misuse, incorrect installation, and (or) dangerous environment. When connecting the device it is crucial not to have the power of the 9223K connected. 1. ) First connect the cables to the 9223K. Make sure that you have stripped enough of the cable so that the contacts can fit into the 9223K. During this part you will need to decide whether each relay will start normally open or normally closed. Once you have decided, carefully unscrew the inputs and place the contacts into the input area and screw on tightly. 2. ) Plug in the network cable RJ45 into the 9223K 3. ) After correctly installing steps 1 and 2 for the very last step plug in the power cable that came with 9223K. Internet Accessible Setup To be able to access the 9223K through the internet, the user must port forward on the router. Since each router is different, please refer to the routers manual on how to port forward the device. Once the device has been successfully port forwarded the use can connect the device from the internet. - 10Ref#9223K05260001 For example If the 9223K IP Address: 192. 168. 100. 200 Port: 9223 On the router you will need to port forward the IP Address 192. 168. 100. 200 on Port 9223. 5. ) IP Edit Search Tool Using IP Edit IPEdit is a search tool designed to setup and access the IP Power 9223K. IP Service is an additional feature which searches for the device easily without having to remember long complicated IP addresses. Instead, this technology allows the user find his or her device through the internet just by device name. Note: Please allow the IP Power 9223K 1 to load before using IPEdit. If the device is found double click on the Local devices section and a IE window should pop up to the login of the device Default IP: 192. 168. 1. 100 Default Login: admin Default Password: 12345678: 1. ) After you have logged into the device you will be required to install active x controls. If this screen does not appear make sure you allow active x. GPIO Configuration Set I/O The Set I/O configuration is where most of the live power control is done. From this panel the user can directly turn off power, set timers and turn power back on. PIN I/O The Pin I/O column is the labels for the ports on the device. By default the output ports are labeled as Out1, Out2, Out3, & Out 4. To rename these default labels please see section "Definite I/O Name" for direction. - 14Ref#9223K05260001 Note: Please remember that you use normally open or normally closed the output control will either create a open circuit or a closed circuit. [. . . ] Local Time: The local time gets the time of the PC that is currently being used. 7. ) Controlling the Device CGI HTTP Commands Http commands allow you to control the device with commands. There are two ways to input http commands with authorization required Password in http: http://login:password@ipaddress:port/command Password not in http: http://ipaddress:port/command Note: If you use the password not in http: command you will need to enter it when the browser asks for the password. Help Command The help command will give you the commands that are available on the device. Simply type the codes for the correct code. http://192. 168. 1. 3/help - 21Ref#9223K05260001 Output: Set Power Command The Set Power command allows you to control the devices on/off through the http commands. [. . . ]