User manual AVISION DS610CF

[. . . ] DS610CF User's Manual (D/N: 250-0245-E Rev. 1. 0) Avision, Inc Trademarks Microsoft is a U. S. registered trademark of Microsoft Corporation. Windows and MS-DOS are trademarks of Microsoft Corporation. [. . . ] The Message Window displays "Normal mode". Repress the "Normal/Quality" button and the Message Window displays "Quality mode". The copying begins processing with the Quality mode. 1. 2. See following photo/text reproduction between normal copier v. s. DS610CF in quality mode. Make copies with a normal copier Make copies with a DS610CF in quality mode ã Note: · To proceed copies using quality mode, make sure your printer has at least 4M memory as this requires more processing time. 3-13 3. 4. 8 FOCUS ON PHOTO COPY, TEXT COPY, OR MIXED PHOTO & TEXT COPY If the content in the original is occupied by photo images only or by photo images with a little text on it, press to select the Photo function to get a photo-concentrated image copy. On the contrary, the Text function helps you get a textconcentrated copy. However, if the proportion of the photo image is almost the same as that of text in the original to be copied, it is recommended to utilize the Auto function from Auto/Text/Photo button in order to get the most optimal printout with photo and text mixed. The Operating Steps: Place your document face-down on the document glass. Keep on pressing "Auto/Text/Photo" button to select any one of these 3 document-type functions, called Photo, Text, and Auto. Press the Copy button, and the printout shows the best reproduction with the document-type concentration selected. 1. 3-14 - 3. 4. 9 MAKING COPIES OF A 3D OBJECT The DS610CF solution improves your copy reproduction significantly and even makes a 3D object copies amazingly clear. The Operating Steps: Place your 3D object on the document glass. Press the "Normal/Quality" button and the Message Window displays "Normal mode". Repress the "Normal/Quality" and the Message Window displays "Quality mode". 2. The 3D copy using a normal copier The amazing 3D copy using the DS610CF 3-15 3. 4. 10 AUTOMATIC POWER SAVING The DS610CF features automatic power saving without unplugging the power cable. If you either have not used the DS610CF over a selected power-saving interval (15 minutes, 2 hours, 4 hours, or no power saving) or simply press the Power Saving button , it automatically turns into power saving status. To resume the ready status, press any one of the button on the Control Panel. The Message Window displays "Warming up. . . " and then "1 Copy @100%", the ready status. The Ready LED now turns steadily on. 3-16 - 4. USING DS610CF AS A SCANNER To run DS610CF at optimum speed, the following minimum requirements are recommended: · · · · · · · · IBM compatible PC 386/486, Pentium or later; Microsoft Windows 95/98/Me/2000, Windows NT; One printer port available :ECP or EPP(enhanced parallel port); 20 Megabytes of available hard disk space for installation; 16 Megabytes of RAM (32 Megabytes or higher recommended); A video graphics array (VGA) monitor; A Microsoft Windows-compatible pointing device (e. g. , mouse); A CD ROM drive. 4. 1 INSTALLATION PROCED URE Installation procedures of DS610CF driver are as follows: 1. Insert software CD into your CD ROM drive. 4-17 3. Press the Start button, choose RUN, type d:\driver\setup. exe (d: the CD-ROM drive in use), and then click O. K. Follow the on-screen instructions to complete the installation. Fig. 3. 2 4-18 - 4. 2 DOWNLOADING PRINTER COLOR TABLE Download compatible printer color table files to DS610CF before making copy with DS610CF. [. . . ] Select Flatbed source at the top of the TWAIN window. Press the Preview button to get an initial scanned image at a low resolution image to allocate your selected scan area. Finally press the Scan button on the bottom of TWAIN window or the Scan button on the Control Panel. YA M MAY 0 A6 A5 B5 LTR A4 LGL 9-11 The Preview Button The Scan Button 9-12 - 9. 3 MAINTAINING THE ADF 9. 3. 1 CLEANING THE ADF The DS610CF is designed to be maintenance free. However, it still needs to be cleaned occasionally to ensure optimum image quality and performance. [. . . ]