User manual AVISION FB6000

[. . . ] Avision FB6000 Color Image Scanner User' Manual s Installing the Scanner Installing the Software Editing Your Image Maintenance Troubleshooting i Trademarks Microsoft is a U. S. registered trademark of Microsoft Corporation. Windows and MS-DOS are trademarks of Microsoft Corporation. IBM, PC, AT, XT are registered trademarks of International Business Machines Corp. [. . . ] Note: The factory setting for the scanner is ID# 6. Usually, ID# 0 is assigned to an internal hard disk drive, and ID# 7, to SCSI adapter or host. ID# 8 and #9 are not in use. 2. 4 SETTING SCSI TERMINATOR The scanner is equipped with a built-in terminator switch on the rear side of the scanner (See also Figure 2-2). Move the switch to the "on" position to enable the SCSI termination or to the "off" position to disable the SCSI termination. The SCSI termination ensures the electrical signal flow through the SCSI chain properly. As a result, if the scanner is the only or final device connected to your computer, you should enable your SCSI chain terminates at the scanner by moving the terminator switch to the "on" position. If your scanner is linked between the host computer and other SCSI devices, then the SCSI chain should terminate at the final SCSI device. In the case, disable your SCSI termination on the scanner by moving the terminator switch to "off" position. ) 2-3 1 2 1. 2. SCSI ID Setting SCSI Terminator Switch Figure 2-2 SCSI ID setting/Terminator switch 2-4 2. 5 SETTING SCSI SYNC SWITCH The scanner is designed with a SCSI SYNC switch at the rear of the machine. The default setting is "OFF" If the SCSI card of your . computer supports SYNC, please move the SYNC switch at the rear of the scanner to the "ON" position to make the data transmission faster. ON OFF SYNC Switch Figure 2-3 SCSI SYNC Switch 2-5 2. 6 CONNECTING THE CABLES Be sure the scanner power is switched off. Connect the power cable and SCSI cable as shown in Figure 2-4. Scanner Power cord To a computer SCSI cable To a power outlet Figure 2-4 Cable Connection 2-6 2. 7 PLACING YOUR ORIGINAL Open the document cover then place your original face down on the document glass as shown in Fig. Make sure the top of your original near the document alignment mark. 1 2 3 4 1. 4. Document cover Document alignment mark Your original Document glass Figure 2-5 Placing the original 2-7 3. SCANNER DRIVER INSTALLATION SYSTEM REQUIREMENTS 3. 1 To run the color image scanner at optimum speed, the following minimum requirements are recommended: IBM compatible PC Pentium III 600 or above; Windows 95, Windows 98, Windows ME; One SCSI card installed one your computer; 100M bytes of available hard disk space for installation; 128M bytes of RAM or above; A video graphics array (VGA) monitor; A Microsoft Windows-compatible pointing device (e. g. , the mouse); A CD-ROM drive. 3. 2 1. 3. INSTALLATION STEPS Start Windows 98 / 98SE / Me / 2000 / XP . Insert the supplied CD-ROM into your CD-ROM drive. An installation menu will be automatically displayed. If the installation menu has not been automatically displayed on your screen, please press the "Start" button and choose RUN, type "d:\cdsetup. exe" ("d:" the CD-ROM drive letter in use). Follow on-screen instructions to complete the installation. 4. 3-1 3. 3 SCANNING WITH IMAGE EDITING SOFTWARE The scanner driver is not a stand-alone program, it has to be started from within a TWAIN-compliant or plug-in software application and then the scanner driver is able to scan and load the image to your computer. The command to start the scanner driver may vary due to different software applications. Start a TWAIN compliant software application such as Roxio PhotoSuite 4 SE which is bundled in the CD. Click Get>Scanner (TWAIN). 3. Choose FB6000 as your scanning source. 6. Place the document FACE DOWN on the document glass. [. . . ] Your scanner is now ready for use. 1 1. Document glass Figure 5-1 The cleaning area 5-1 6. TROUBLESHOOTING If you have problems with the operation of your scanner, please check the following troubleshooting hints. 6. 1 FREQUENTLY ASKED QUESTIONS Question: Answer: When the scanner is powered on, it makes noises and won't stand ready. There are two possibilities: 1) You might fail to push the scanner shipping lock to its "use" position. If this is the case, pull the scanner status switch to its "use" position first. [. . . ]