User manual AVITAL DIABLO 2

[. . . ] þ Instant Remote Control Code Deletion -- Removes the code of a lost or stolen remote control to prevent unauthorized alarm operation. þ Electronic Scan Prevention (ESP) -- ESP blocks electronic scanner codes to prevent disarming of your vehicle by anyone but you. þ Remote Panic with Safety LocksTM -- In a threatening situation, you can activate the siren, flash the parking lights and unlock the doors for immediate entry into your vehicle (may require optional relays). 2 Diablo /AMX 68/AT-58 Owner's Manual 12/29/97 2 þ Interior Light Illumination Capability -- When remotely disarmed, the alarm system turns on the interior lights for 30 seconds or until the ignition key is turned on (requires an optional relay). þ Multi-Zone Protection -- Offers full perimeter security with separate trigger connections for the doors, hood and trunk (may require optional switches). [. . . ] See the "Programming Table for Alarm Features" on page 9. n n Active Arming. The siren will chirp twice, the parking lights will flash twice, the doors will lock, the LED will flash slowly and the starter will be disabled. Turn the ignition key off, exit the vehicle and close the doors. When the interior lights turn off, the LED will flash rapidly for 30 seconds to indicate the system is passive arming. The LED will then flash slowly to indicate the system is armed and the starter is disabled. (At any time during passive arming, you may actively arm the alarm. ) n n To Disarm the System -- Press remote button #1 for 1-2 seconds. The siren will chirp once, the parking lights will flash once, the doors will unlock, the interior lights will turn on (if the optional interior light illumination relay was installed), the LED will turn off and the starter will be enabled. 5 Diablo /AMX 68/AT-58 Owner's Manual 12/29/97 2 n To Silently Arm or Disarm the System -- Press remote button #3 for 1-2 seconds. n Silent Arm Indications. The parking lights will flash twice, the doors will lock, the starter will be disabled and the LED will flash slowly. The parking lights will flash once, the doors will unlock, the starter will be enabled and the LED will turn off. n n Interior Light Illumination Capability -- When the alarm system is remotely disarmed, the vehicle's interior light(s) will turn on for 30 seconds or until the ignition key is turned on (requires an optional relay). To Activate an Accessory -- Press remote button #2 for 1-2 seconds to activate an optional accessory such as trunk release, remote engine starter or a remote control garage door opener. Valet Switch -- The valet switch is a small hidden toggle switch that allows you to program many features of the alarm system and prevent passive arming. In the event of a lost or stolen remote control, you can also use this switch to bypass (shut off) the alarm system. BE SURE TO ASK YOUR DEALER TO SHOW YOU WHERE THE VALET SWITCH IS LOCATED. n n If passive arming is turned on, you should put your system in Valet Mode when your car is being serviced by mechanics, car wash personnel or driven by valet attendants. While in Valet Mode, all alarm functions are bypassed to prevent undesired or accidental arming. n To Turn on Valet Mode 1. Turn your ignition key to the "ON" position or start the vehicle. Flick the valet switch to the "ON" position. The LED will turn on solid red to indicate the alarm is in Valet Mode. 6 Diablo /AMX 68/AT-58 Owner's Manual 12/29/97 2 n Turn off Valet Mode 1. Turn your ignition key to the "ON" position or start the vehicle. Flick the valet switch to the "OFF" position. The LED will turn off to indicate the alarm is no longer in Valet Mode. n User Programmable Passive Door Locking -- The system will not automatically lock the doors when the alarm passively arms to prevent the keys and remote from accidentally being locked in the vehicle. If you prefer, you can easily program the alarm to automatically lock the doors every time the alarm passively arms. See the "Programming Table for Alarm Features" on page 9. To Activate Remote Panic -- Press and hold button #1 for 3-4 seconds. [. . . ] Turn the ignition key to the "ON" position. Within 10 seconds, begin flicking the valet switch on and off. The siren will chirp one time each time you flick the switch on, then off. Continue flicking the switch on and off until you reach the number of chirps associated with your chosen feature. NOTE: Stop on the chirp. 6. [. . . ]