User manual AXIS 2400AM

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual AXIS 2400AM. We hope that this AXIS 2400AM user guide will be useful to you.

Lastmanuals help download the user guide AXIS 2400AM.

Download

Manual abstract: user guide AXIS 2400AM

Detailed instructions for use are in the User's Guide.

 [. . . ] Administration Manual

AXIS 2400/01 Video Server
Professional Surveillance and Monitoring over TCP/IP

Includes support for AXIS 2191 Audio Module

2

AXIS 2400/2401 Admin Manual About This Document
This manual is intended for both administrators and users of the AXIS 2400/2401 Video Server,  and is applicable for software release 2. 31. It includes simple step-by-step instructions for configuring,  managing and using the AXIS 2400/2401 Video Server on your network. Previous experience of networking will be of use to the reader when installing and using this product. Some knowledge of UNIX or Linux-based systems would also be beneficial,  for developing custom PHP-based programming scripts and applications.  [. . . ] · EMC · Full-duplex audio: Audio data encoded in ADPCM format at 32kbps,  8 kHz sampling (G. 721). · 9-pin D-SUB serial connector: RS-232. · Power Input: Axis PS-D power supply. · Line Out: Unbalanced,  0. 05-1. 0Vpp · Line Input: Balanced 0. 05-1Vpp. Connect source ground to pin 2 and source signal to pin 1 if the source is unbalanced. · Speaker Output: Balanced,  0. 5W. Connect directly to speaker without capacitors. · Alternative Power: 12-15VAC,  min 10VA,  or 15-20VDC,  min 7W. · Metrics: Height: 1. 1" (27mm),  Width: 4. 4" (112mm),  Length: 4. 3" (110mm),  Weight: 0. 7lb (0. 32kg). · Maximum number of users: 10 (on local area network). 

Connection Diagram

The Audio Module to Video Server Serial Cable
The serial cable supplied with your AXIS 2191 is wired as shown in the table:

Pinouts for the RS-232 Port Audio
IN IN OUT OUT GND IN OUT IN Unused

Pin
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9

Pin
IN IN

Server

Signal
CD RXD TXD DTR GND DSR RTS CTS RI

OUT OUT GND IN OUT IN IN

38

Other IP Setup Methods

AXIS 2400/2401 Admin Manual

Appendix A - Other IP Setup Methods

As an alternative to the ARP command (described earlier in the Installation section of this manual),  you can set the IP address for your AXIS 2400/2401 using any of the following methods - as appropriate for your operating system:
Method AXIS IP Installer Operating Systems Windows Refer to. . . Using the AXIS IP Installer,  on page 39. 

BOOTP Requiring a BOOTP daemon on your system,  this method operates over the entire network. A request to an active daemon initiates a search of the boot table to find an entry matching the unit's Ethernet address. The daemon downloads the IP address to the device if a match is found. 

UNIX

Notes:

·Make sure the AXIS 2400/2401 is powered up and connected to the network. ·IP Address: Acquire an unused IP address from your Network Administrator,  and do NOT use the default IP address featured in the following examples when installing your AXIS 2400/2401. ·Server Privileges: Although no special privileges are required for Windows 95/98/ME or XP (Home),  you will need Administrator privileges for Windows NT/2000 and XP (Professional). UNIX systems require Root privileges. 

Ethernet/Mac Address: The AXIS 2400/2401 is pre-configured with a unique Ethernet/Mac Address based upon the serial number printed on the underside label of the unit; where the serial number typically follows the format 00-40-8c-xx-yy-zz. You need this address to complete the installation. 

Notes for Macintosh Users
When using the AXIS 2400/01 on a Macintosh,  please observe the following points: · The AXIS 2400/2401 has a default IP address of 192. 36. 253. 80. · Assign a temporary IP address to a Mac workstation in the same subnet (e. g. 192. 36. 253. 81) and then connect to the server. · Run the Installation wizard and set the desired IP address for the server. · Reset the correct IP address for the Macintosh workstation. · Changing the IP address for a Macintosh does not require a reboot.  [. . . ]  Conecte la fuente de alimentación a la AXIS 2400/2401 y compruebe que el Indicador de corriente está encendido. Desde el menú Inicio, 
abra el Panel de control y haga doble clic en el icono Módems. 

 Active la casilla de verificación:
No detectar el módem,  lo seleccionaré de una lista. Haga clic en Siguiente>. 

 Si ya hay un módem estándar configurado,  haga clic sobre Cancelar y proceda a la siguiente página. En caso contrario,  haga clic sobre Añadir y continúe con el paso 5. 

Seleccione el módem estándar 28800 de la
lista de módems.  [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE AXIS 2400AM

Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets...
In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.

Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual AXIS 2400AM will begin.