User manual AXIS 250S BLADE INSTALLATION GUIDE

[. . . ] Compliance is not valid for unshielded network cables. Liability - Every care has been taken in the preparation of this manual; Please inform your local Axis office of any inaccuracies or omissions. Axis Communications AB cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice. Axis Communications AB makes no warranty of any kind with regard to the material contained within this document, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. [. . . ] This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Europe This digital equipment fulfills the requirements for radiated emission according to limit B of EN55022, and the requirements for immunity according to EN55024 residential, commercial, and light industry. Battery Replacement - The Axis Rack Mounted Video Server Solution uses a 3. 0V CR2032 Lithium battery as the power supply for its internal real-time clock (RTC). This battery will, under normal conditions, last for a minimum of 5 years. Low battery power affects the operation of the RTC, causing it to reset at every power-up. A log message will appear when battery replacement is required. . The battery should not be replaced unless required!If the battery needs replacing, please observe the following points: · Caution!Danger of explosion if battery is incorrectly replaced · Replace only with the same or equivalent battery, as recommended by the manufacturer · Dispose of used batteries according to the manufacturer's instructions Japan - This is a class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and AXIS COMMUNICATIONS <Product Name> Quick User's Guide AXIS 250S Blade - Rack Solution Installation Guide The Axis Video Server Rack will fit up to 12 rack mounted Axis Video Servers (Blade Servers). This installation guide describes the hardware installation of the Axis Rack Mounted Video Server Solution. The AXIS 250S Video Server User's Manual contains additional instructions on the following: · Installing the video server · Configuring the video server · Using the video server · Troubleshooting · Updating the software · Customizing the video server 3 Hardware Inventory - AXIS Video Server Rack Please contact your dealer if anything is missing or damaged. Qty 1 5 1 2 1 1 Item Video server rack Cover plates Cover plate Connectors Power supply Power Cable Country-specific: ensure that the correct adapter is used Warranty Document Product Name/Title AXIS Video Server Rack Cover plate 12TE Cover plate 6TE Terminal Connectors 6p Power Supply 19" 100W Mains Cable IEC Europe UK US / Japan Australia Country 1 Hardware Inventory - Axis Blade Video Server Please contact your dealer if anything is missing or damaged. Qty 1 2 1 1 1 Item Video servers Connectors Warranty Document User's Manual This Document AXIS 250S User's Manual AXIS 250S Blade - Rack Solution Installation Guide Title/Variants AXIS 250S Blade Terminal Connectors 14p 4 AXIS 250S Blade - Rack Solution Installation Guide AXIS 250S Blade Video Server Read the following information to familiarize yourself with the AXIS 250S Blade video server making particular note of where the connectors and indicators are located: Control Button See the AXIS 250S User's Manual for information on the use of the control button. Indicators Power Green Amber Status Green Red Network Amber Green Red None Flashes amber during firmware upgrade Normal operation Flashes rapid red for a critical error Flashes for activity on a 10 Mbit/s network Flashes for activity on a 100 Mbit/s network No network connection No connection Control Button Normal operation Flashing green or unlit for power supply failure Connectors MIC LINE VIDEO IN Microphone connector Line connector Y/C video input (S-video) Video Input (BNC) connection is made using an s-video cable connection is made using an RG59, 75 Ohm coax video cable; with a recommended maximum length of 800 feet (250 meters). P/N: XXXX-YYY-ZZ S/N: 00408C1A2B3C Top and bottom screws are used to secure the blade server in the rack Product Label S/N (serial number) is identical to the unit's MAC/Ethernet address, e. g. P/N (part number) is the product model number. AXIS 250S Blade - Rack Solution Installation Guide 5 AXIS 250S Blade 1 Switch - for selecting 75 ohm video termination (for BNC). 2 Bus Connector - connected to the I/O terminal block connector at the back of the rack. 1 2 Axis Video Server Rack DC-Power (GND) Power Connector DC+Power I/O Terminal Blocks Network Connectors The I/O Terminal Block - the physical interface to a relay switch output and four digital photo-coupled inputs; also providing an RS-485 interface and an RS-232 serial connection. Network Connector - Axis blade video servers are designed for 10 Mbps Ethernet /100 Mbps Fast Ethernet networks and connect to the network via a standard RJ 45 connector. [. . . ] When repeating the installation procedure for each individual blade video server, simply disconnect the blade video server from the rack (i. e. · Secure the video server to the rack using the screws on the front panel. The rack accommodates up to 12 individual Axis Video Servers. To comply with EMC regulations, ensure that all empty slots are covered using the supplied cover plates. AXIS 250S Video Server User's Manual The functionality of the Axis Blade Video Servers is the same as in the standalone versions. [. . . ]