User manual AXIS 5670E

[. . . ] AXIS 5570e/AXIS 5670e Host-to-LAN Print Servers User's Manual AXIS 5570e / AXIS 5670e User's Manual 1 Regulatory Information Safety Notices Important: Take some time to read through the safety notices before installing the print server. Please observe all safety markings and instructions when using this product. Observe "Important:" in the text to avoid operational impairment. Do not proceed until you have fully understood the implications. Electromagnetic Compatibility (EMC) USA This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. [. . . ] To start the configuration, the command %CONFIG+ is entered in the file. To protect your settings, a password must be provided. When all parameters are set, the command SAVE is used to store the parameters permanently. The command %CONFIG- leaves the configuration mode and resumes normal printing. The syntax for the file to print is: %CONFIG+ <password;> IBM_PRINTING_PARAMETER_NAME = VALUE; SAVE; %CONFIG- In order to maintain backward compatibility and increase security, many parameters that are not related to the IBM printing operation have to be preceded by the %CONFIG++ command. When all parameters are set, enter %CONFIG--. The parameters requiring %CONFIG++ are clearly marked in the parameter listing on the following pages. %CONFIG+ <password;> IBM_PRINTING_PARAMETER_NAME = VALUE; %CONFIG++ PARAMETER_NAME = VALUE; %CONFIG-SAVE; %CONFIG- 142 AXIS 5570e / AXIS 5670e User's Manual Management and Configuration Select the PCL5 printer driver and disable the NetWare protocol: %CONFIG+ password; PRDRIVER = PCL5; %CONFIG++ NETW_ENB = NO; %CONFIG-SAVE; %CONFIG(If you have not changed the default password (pass), the password is optional) For parameters requiring more than one value, the values should be separated using a comma. AXIS 5570e / AXIS 5670e User's Manual 143 Configuration Possibilities Section 12 Configuration Possibilities This section describes some special features offered by the AXIS 5570e/AXIS 5670e: Autodetect Printer Type, on page 144 Auto-IP, on page 144 Changing Language in the Print Server's Web Interface, on page 145 E-mail Notification, on page 145 Flash Loading of Firmware over the Web, on page 162 IPP (Internet Printing Protocol), on page 146 Logical Printers for Customized Printing, on page 154 Network Speed, on page 161 NetWare Packet Signature Levels, on page 162 Overriding Port Status, on page 168 TCP/IP Restrictions, on page 163 Enabling Secure Web Services -- SSL/TLS, on page 164 Autodetect Printer Type The print server can automatically detect the type of printer you are using if you enable Autodetect Printer Type. The print server can then recognize Epson and Hewlett Packard InkJet printers. Most Epson and Hewlett Packard InkJet printers that have Mac OS printer drivers for network printing are supported. If Autodetect Printer Type is disabled, the AppleTalk printer type has to be specified manually in the print server. For Epson InkJets it would be "EPSONLQ2" and for HP InkJets it would be "DeskWriter". If the print server does not recognize the connected printer the default setting, "LaserWriter" will be used as printer type. "LaserWriter" is the recommended setting to be used with all PostScript printers. To enable Autodetect Printer Type, log in to your print server's Web interface and select Admin | Network Settings | Detailed View | Macintosh | Auto Detect Printer Type | Yes. See the Help pages in the print server's Web interface for details. Auto-IP In the absence of an IP address management mechanism such as DHCP, the print server will receive a temporary IP address automatically over 144 AXIS 5570e / AXIS 5670e User's Manual Configuration Possibilities Auto-IP, a method which enables the host to automatically take a linklocal IPv4 address. Auto-IP is supported by Windows 98, Me, 2000, XP and Mac OS version 8. 5 or higher. See "Dynamic IP Address Assignment" on page 16. Changing Language in the Print Server's Web Interface English, French, German, Italian, Japanese and Spanish is supported in the print server's Web interface, with English as the default language. You can change the language used for the print server's Web interface from the User mode: 1. Click the Change button next to Language. Choose your preferred language and character set from the drop-down lists, click OK and then press F5 to refresh the view. You can change the Character Set by clicking the Change button. The default Character Set is ISO-8859-1, which can be applied in most cases. [. . . ] A way of specifying the location of publicly available information on the Internet. Virtual Printer Driver Interface Virtual Telecommunications Access Method. Mainframe software that performs network control and management. VTAM's most important objective is to provide the SSCP services. [. . . ]