User manual BABYMOOV BABYPHONE HIGH CARE

[. . . ] BABYPHONE HIGH CARE • Notice d’utilisation 7 Contrôle de distance Lorsque Elo est sélectionné, l'icône de contrôle de distance apparait : le récepteur émet une alarme lorsque la distance entre l'émetteur et le récepteur dépasse 25 m. Alarme de distance Cette fonction de contrôle de distance peut être utile pour surveiller les activités d'un enfant dans un parc ou dans sa chambre. Dans le cas où l'émetteur est réglé pour fonctionner avec la fonction de contrôle de distance, le récepteur entrera automatiquement dans le mode de contrôle de distance (comme indiqué par la lettre sur l'écran LCD), que le réglage hors de portée soit sur ON ou sur OFF. Réglage d'alerte hors de portée dans l'émetteur ON ON OFF OFF ELo Réglage d'alerte hors de portée dans le récepteur ON OFF ON OFF ON ou OFF Remarques L'alarme fonctionne normalement Aucune alarme même hors de la portée Donne toujours une alarme, hors de portée ou non Aucune alarme même hors de la portée Alarme sonore quand la distance dépasse 20-30m (à condition que apparaisse sur l’écran LCD du récepteur) 4. [. . . ] Repeat the above steps, besure you also program the receiver with the same new channel and digital code. Power choice Note with low power, the communication distance will become shorter but the battery life can be prolonged. Besides, the level of emitted radiation is also reduced. Distance alert This distance control function may be useful to watch baby’s activities in his room. The transmitter is placed on the child and if he moves away more than 25 meters, an alert will be heard from the receiver to alert parents. : if the out of range function is already On on the transmitter, the receiver will automatically activate the distance alert (as indicated by the letter on the LCD screen), wether the out of range setting is On or Off. Out-of-range alert setting in Transmitter ON ON OFF OFF ELo Out-of-range alert setting in Receiver ON OFF ON OFF ON or OFF Remarks Alarm function normally No alarm even when out of range Always give alarm no matter out of range or not No alarm even when out of range Alarm sound once distance apart exceed 20-30m (provid appears on rerceiver LCD) 4. Temperature alarm • It is recommended to have at least ±5°C between the settings of upper and lower temperature limit from the current temperature reading, otherwise the temperature alarm can often be heard whenever the baby’s room temperature changes lightly. € In case there is a sudden temperature change, the sensor may need to take a few minutes before it can settle to the new environment and show the correct reading on the screen. € Caution : because of the heat produced bu the device itself, a margin of error + 5°C may be noticed. Please add 5°C to the upper and lower temperature to consider this gap. OPERATION A / Transmitter • Place the transmitter about 1 m from the cradle, directing the microphone (5) towards the baby. € Use the selection button (2) to adjust the microphone sensitivity (volume indicator = bar chart on the screen). The more bars you show, the more sensitive the microphone is to sounds. € As soon as the transmitter detects a sound, the screen lights up and the transmission symbol is displayed. BABYPHONE HIGH CARE • Instruction Manual 17 • To ckeck your settings, press briefly on the receiver mode button (3). The various settings will be displayed according to a cycle : Current baby’s room temperature EOut of range larm condition Selected channel and digital code Selected output power • The night light (4) can be set permanently ON by moving the power ON/OFF switch to position . The night light can also be set to be VOX (voice activated) by momentarily pressing the mode button (3) : the VOX icon will be shown besides the icon . Under VOX mode, the night light will be switched on once the microphone 5 detects a sound and automatically goes off a few seconds after the microphone 5 stops picking up any sound. € The condition of the battery is shown by the battery status indicator . When the battery power is being consumed, the segments within the battery status indicator gradually falls. Once the indicator becomes empty it will start flashing, besides, the transmitter will also send out a signal to the receiver to alert the parents. [. . . ] € Interferences with other appliances operating on the same channel. € The out-of-range setting on the transmitter and the receiver is on Off. € The out-of-range alarm setting in the transmitter is on On but the setting in the receiver is on Off. € Change the setting on the receiver to On. [. . . ]