User manual BARRACUDA C400 INSTALLATION REV 1.3

[. . . ] 16 Serial Connection via Console Port . 16 4 General Introduction The information in this user guide has been carefully reviewed and is believed to be accurate. It is valid from Barracuda NG Firewall firmware version 5. 0. Barracuda Networks assumes no responsibility for any inaccuracies that may be contained in this document. [. . . ] Handle a board by its edges only; do not touch its components, peripheral memory modules or contacts. When handling chips or modules, avoid touching their pins. Put the server board and peripherals back into their antistatic bags when not in use. For grounding purposes, make sure your computer chassis provides excellent conductivity between the power supply, the case, the mounting fasteners and the server board. After accessing the inside of the system, close back the system and secure it to the rack unit with the retention screws after ensuring that all connections have been made. · 7 Safety Instructions Introduction and Package Contents Your new Barracuda NG Control Center C400 is a management appliance preinstalled with firmware to centrally manage Barracuda NG Firewall appliances in a secure, reliable and efficient way. Hardware Configuration Table 1 Hardware Component CPU Memory HDD Flash Disk Form Factor Dimensions (W/D/H) Net Weight Power Supply Input Voltage Power Supply Frequency Storage Temperature Operation Temperature Relative Humidity Certifications Description AMD Athlon dual core 2 GB 2 x 3. 5" 250 GB, 7200 rpm 4 GB 1U Full Size 42. 7 x 4. 3 x 57. 4 cm 11. 8 kg 100 - 240 V, AC 47 Hz - 63 Hz -20 °C - +70 °C 0 °C - 40 °C 5% - 95%, non-condensing CE, FCC, ROHS The hardware configuration list in Table 1 was valid at the time this manual was published. The listed components are subject to change at any time, as Barracuda Networks may change hardware components due to technological progress. Therefore, the list may not reflect the current hardware configuration of the Barracuda Networks NG Firewall or NG Control Center appliance it was delivered with. Inspecting the Package The following items are included in the package: · · · · One security appliance One power cord Printed Quick Start Guide One USB flash drive including documentation and administrative tools Please contact Barracuda Networks support if any of these items is missing. 8 Appliance Installation Guide Powering Up and Down This chapter describes the procedure used to install your appliance and perform the initial configuration. Powering Up the Appliance · · · · Connect and power on the appliance. The current status of the boot process will be shown on the appliance's LCD display. You may also use the serial console for this purpose. After a few seconds, the boot process will be initiated and the status LED should start to blink green. Wait until the status LED indicates constant green: The booting procedure is finished. Powering Down the Appliance You must never turn off the appliance by simply switching it off or otherwise removing power from it. Always initiate a proper system shutdown as described below. · · · The system shutdown must be initiated either using the Barracuda NG Admin tool, a remote logon to the appliance or by using the LCD display and keypad on the appliance. The current status of the shutdown process will be shown on the appliance's LCD display. You may also use the serial console for this purpose. The status LED will turn off at the end of the shutdown procedure. 9 Powering Up and Down The Status LED Your appliance is equipped with a variety of LEDs. It is either labeled with a heart symbol or the term Status. It indicates the appliance's operational state by changing colors between green, orange and red and by changing between blinking and steady glowing. The table below shows the different meanings of the different glowing states. Table 2 Status LED Conditions Color Off Glowing State Off Meaning Installation Appliance is powered off or installation has not initialized far enough for LED control when installation is started. Installation was completed successfully, appliance is halted for reboot or installation was not yet initialized far enough for LED control. Meaning Normal Operation or ART Appliance is powered off. Appliance is either booting, shutting down or performing a system update. Barracuda NG Firewall is up and running. An error has appeared preventing Barracuda NG Firewall from entering the up state. Green Blinking Green Steady Red Blinking Error during installation. If no orange light available: appliance is in ART mode. [. . . ] Boot into the ART menu as described above in (the Status LED blinks orange when ART is running) and choose Start recovery. Then, follow the on-screen instructions. Recovery is finished as soon as the Status LED steadily indicates green. · · 13 Installation and Recovery Using ART Errors During Recovery If difficulties are encountered during the recovery process, the Status LED will blink red. Furthermore, you may also trace the output using the serial console. 14 Appliance Installation Guide Connecting to the Network and Configuring Fig. [. . . ]