User manual BARTSCHER A120408-116

[. . . ] If it is placed on a fitted or loose carpet, adjust the feet in such a way as to allow enough room for ventilation beneath the washing machine. Check whether the washing machine has been damaged during transport. If this is the case, do not install it and contact your retailer. Remove the four protective screws and the rubber washer with the respective spacer, situated on the rear of the appliance (see figure). [. . . ] When the programme has ended, the word END is displayed. Take out your laundry and leave the appliance door ajar to allow the drum to dry thoroughly. Turn the washing machine off by pressing button . ) Slightly soiled delicate colours 1 2 3 4 5 90°C 90°C 60°C 40°C 30°C • • • • • • • • • • • 147 130 115 82 75 Pre-wash, wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, intermediate and final spin cycles Wash cycle, rinse cycles, anti-crease or delicate spin cycle Wash cycle, rinse cycles, anti-crease or delicate spin cycle Wash cycle, rinse cycles, anti-crease or delicate spin cycle Wash cycle, rinse cycles, anti-crease or delicate spin cycle Wash cycle, rinse cycles and delicate spin cycle Wash cycle, rinse cycles and delicate spin cycle Wash cycle, rinse cycles, anti-crease or draining cycle Rinse cycles and spin cycle Rinse cycles, anti-crease or draining Draining and heavy duty spin cycle Draining and delicate spin cycle Draining Synthetics Heavily soiled fast colours (baby linen, etc. ) PARTIAL PROGRAMMES Rinse Delicate rinse cycle Spin cycle Delicate spin cycle Draining • • 10 11 40°C 30°C • • • • 50 45 Notes For the anti-crease function: see Easy iron, opposite page. The information contained in the table is purely indicative. Special programme Daily 30' (programme 9 for Synthetics) is designed to wash lightly soiled garments in a short amount of time: it only lasts 30 minutes and allows you to save on both time and energy. By setting this programme (9 at 30°C), you can wash different fabrics together (except for woollen and silk items), with a maximum load of 3 kg. we recommend the use of liquid detergent. 6 Personalisations If, when the appliance is switched on, the KNOB is positioned appears. Press on a programme with a spin cycle, a fixed button and the maximum spin speed allowed for the programme set will be displayed, and the icon flashes. all programmes except for 1 , 2 , 9 , 10 and Draining. 1, 2, 3, 4, 5, 6, 7, 8 Service Rapid 7 Detergents and laundry GB Detergent dispenser Good washing results also depend on the correct dose of detergent: adding too much detergent won't necessarily make for a more efficient wash, and may in fact cause build up on the interior of your appliance and even pollute the environment. The following information is provided for your safety and should consequently be read carefully. • Disposing of an old washing machine: before scrapping your appliance, cut the power supply cable and remove the appliance door. GB Installation General safety • This appliance has been designed for nonprofessional, household use and its functions must not be changed. • This washing machine should only be used by adults and in accordance with the instructions provided in this manual. • Never touch the washing machine when barefoot or with wet or damp hands or feet. • Do not pull on the power supply cable to unplug the appliance from the electricity socket. • Do not open the detergent dispenser while the appliance is in operation. • Do not touch the drain water as it could reach very high temperatures. • Never force the washing machine door: this could damage the safety lock mechanism designed to prevent any accidental openings. [. . . ] Before calling for Assistance (see page 12), make sure the problem can't easily be solved by consulting the following list. gB Installation Problem The washing machine won't start. Possible causes/Solution: • The appliance is not plugged into the socket, or not enough to make contact. • A delayed start has been set (using the Delay Timer, see page 7). [. . . ]