User manual BARTSCHER A190141-130

[. . . ] Infrared sensor window Receives the infrared wave from the remote control. MENU/PRESET CH Headphone jack Use to listen to the audio with headphone. Audio input terminal (AV-2 IN) Connects to a camcorder, video game, etc. Video input terminal (AV-2 IN) Connects to a camcorder, video game, etc. If your outdoor antenna uses a 75-ohm coaxial cable with a standard DIN45325 plug (IEC 169-2), plug it into the antenna jack at the rear of the set. If your outdoor antenna uses a 300-ohm twin-lead flat feeder, connect a 300-ohm to 75-ohm impedance converter and plug it into the antenna jack at the rear of the set. / CH Rod antenna connection Antenna mounting socket Rod Antenna Feeder (1) Insert the rod antenna's base post into the antenna mounting socket until it clicks into position. (2) Connect the feeder to the impedance converter. [. . . ] Used for MENU setup. TV/VIDEO Channel selection FEATURE CH-SET TIMER NORMAL PICTURE 1 4 2 5 8 0 3 6 9 1 5 Calls the FEATURE screen. Mutes the sound and restores sound to previous level. !Using CH / CH 7 CH-SET PICTURE Calls the CH-SETTING screen. TV NORMAL Calls the PICTURE screen. • Press CH and channels change as shown below. • Press CH and channels change as shown below. / 2 / 1 / 0 . . . CH CH CH CH FEATURE CH-SET TIMER NORMAL PICTURE @ With the number buttons (on remote control) Displays the channel and timer settings on the screen. 5 • To select a one-digit channel, such as 5, press . If “5-” is indicated, press to select one-digit input, 5 and then press again. • To select a two-digit channel, such as 15, press 1 to select the two-digit input. Press , and then 5 press . TV Resets all settings. -115 SECAM D/K Installing batteries in the remote control unit a With your thumbnail, pull up at the slit to open the battery cover. b Insert two batteries (size AA). c Replace the battery cover. Adjusting volume !Adjust volume using / . • The volume bar disappears approximately three seconds after the volume has been adjusted. VOLUME 10 • When the power indicator lights up dimly, either CH / CH • Channels that have been skipped cannot be selected by CH • The AV1, AV2 input channels cannot be selected using CH these channels. on the TV can be pressed to turn on the power. Use TV/VIDEO to select / A190141-130[EN] 3 7/9/05, 11:22 am E6 PRESETTING CHANNELS E7 SETTING AND ADJUSTMENT Auto channel tuning Automatically tunes in and presets receivable TV stations. Channel setting Enables individual channel setting. AUTO(D/K) VHF 1 48. 25MHz !Press @ Press MENU/PRESET for more than two seconds. again to display AUTO mode screen. changes the screen as shown below. MANUAL Normal screen AUTO !This is useful for timer cooking while you watch TV. Channel / Timer display Displays the current channel number, the timer, and other settings on the screen. !Press . TIMER to call TIMER screen. / / CH TIMER OFF ON POSITION VOLUME --:---:---:-1 4 2 5 8 0 TV/VIDEO CH to select “ ”. to set time. 3 6 9 CH CH 7 TIMER OFF ON POSITION VOLUME --:---:-1:50 FEATURE CH-SET • Maximum time that can be preset is 12 hours and 50 minutes. • The right example shows that the Reminder will be activated after one hour and 50 minutes. CH CH • The time remaining on the Off timer, On timer, and Reminder appears on the screen. • When no timer is set, the channel number, colour and sound system appear on the screen. • Press again to clear these current settings display on the screen. OFF ON 2:30 8:00 1:50 FEATURE TIMER NORMAL PICTURE @ Press again, the channel number, colour and sound system appear on the screen. SECAM D/K 5 TIMER $ Press TIMER to return to normal screen. 0:05 0:04 0:03 0:02 0:01 0:00 TV • Five minutes before the preset length of time expires (in the example, after one hour and 45 minutes) and each minute thereafter, the remaining time appears on the screen for several seconds. • When the preset length of time has passed, “ 0:00” flashes in red. Mute Silences the sound. !Press @ Press level. . ” appears on the screen, and the sound TV/VIDEO • Press , “ is silenced. Flashing , the volume returns to its previous is pressed at any time. TV/VIDEO 1 4 7 2 5 8 0 3 6 9 Number buttons • Mute will be cancelled if the E9 FEATURES CH CH Channel recall Switches back to the channel you were watching just before the current channel. FEATURE CH-SET TIMER NORMAL PICTURE Blue screen Automatically turns the screen blue if a broadcast signal is not received. TV Press FEATURE BLUE BACK ON . !Press @ Press # Press No signal FEATURE to call FEATURE screen. / to select “BLUE BACK” to “ON” or “OFF”. • The channel previously viewed returns to the screen. 5 SECAM SECAM FEATURE to return to normal screen. :ADJUST Example: After switching from channel 5 to channel 7, the channel will change to channel 5. [. . . ] Outlet power OFF. Example use of rear terminals POWER switch of TV not ON. TV For Playback DVD Player For Recording and Editing VCR Yellow : To VIDEO White : To AUDIO Antenna not connected to terminal at the back of the TV set. If outside antenna is used, check for broken wires. Check for local interference. To Audio/ Video out terminals AV-1 IN OUT AUDIO CAUTION : DANGEROUS VOLTAGE INSIDE TO PREVENT ELECTRIC SHOCK. NO UBER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED SERVICE PERSONAL. VIDEO To Audio/ Video in terminals Turn OFF using the POWER switch, then turn ON again after a minute. [. . . ]