User manual BBE SOUND DI1000

[. . . ] If the power cord plug is loose, contact your electrician to replace the defective and unsafe AC Foreign Objects - Be careful that foreign objects and liquids do not enter the enclosure through openings. Cleaning - unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning. USE Power Source - Connect the appliance to a power supply only of the type described in the operating instructions or as marked on the appliance. [. . . ] Research shows that the information which the listener translates into the recognizable characteristics of a live performance are intimately tied into complex time and amplitude relationships between the fundamental and harmonic components of a given musical note or sound. These relationships define a sound's "sound". When these complex relationships pass through a speaker, the proper order is lost. A lower frequency may reach the listener's ear first or perhaps simultaneously with that of a higher frequency. In some cases, the fundamental components may be so time-shifted that they reach the listener's ear ahead of some or all of the harmonic components. This change in the phase and amplitude relationship on the harmonic and fundamental frequencies is technically called "envelope distortion. " The listener perceives this loss of sound integrity in the reproduced sound as "muddy" and "smeared. " In the extreme, it can become difficult to tell the difference between musical instruments, for example, an oboe and a clarinet. conducted extensive studies of numerous speaker systems over a ten year period. With this knowledge, it became possible to identify the characteristics of an ideal speaker and to distill the corrections necessary to return the fundamental and harmonic frequency structures to their correct order. While there are differences among various speaker designs in the magnitude of their correction, the overall pattern of correction needed is remarkably consistent. The BBE Process is so unique that 42 patents have been awarded by the U. S. Patent Office. 4 FRONT PANEL LOW CONTOUR CONTROL Regulates the amount of phase corrected bass frequencies. PROCESS CONTROL Regulates the amount of phase correction. 1/4" INPUT CONNECTOR* IN/OUT TOGGLE The 1/4" input connector of the DI-1000 is unbalanced. The 1/4" SWITCH Engages the Sonic Maximizer Process. input is designed for running instrument cables directly into the DI-1000. 1/4" THRU CONNECTOR* This 1/4 " connector is wired in parallel to the Input connector and is used for continuing the connection to the instrument amplifier. ACTIVE/ PASSIVE SWITCH In the Passive position, the instruments signal is routed straight from the input to the Jensen transformer and then directly to the XLR output. This is a strictly passive, impedance-match only mode. In this mode, the Sonic Maximizer function is not available. In the Active position, the instruments signal is fed to a Buffer Amp with an input impedance of 1Meg Ohm. In this mode the Sonic Maximizer function is available. The signal is then routed to the Jensen transformer balanced XLR output. * WARNING When connecting the speaker level output of a tube amplifier to the input of the DI-1000, a speaker load (cabinet) must be connected to the Thru Connector or damage to your tube amplifier will occur. PAD SWITCH The Pad switch is used to select the desired gain range of the DI-1000. When switched to ­30dB the DI1000 will accept the speaker-level output of your instrument amplifier. 5 REAR PANEL BATTERY COMPARTMENT Use a standard 9Volt battery. Unplugging the input to the DI1000 will turn the unit off and conserve battery life. XLR OUTPUT CONNECTOR The XLR output of the DI-1000 is transformer balanced. The XLR output is used for running from the DI1000 directly into the input of a XLR input of a mixing console. XLR Pin configuration: Pin 1 = Ground Pin2 = Positive Pin3 = Negative. POWER SUPPLY CONNECTOR Connect the included 9VDC power supply here. [. . . ] All charges related to non-UPS shipping, including customs clearance, will be billed. The warranty will be honored for the longer of either 90 days from the date of any service or the remainder of the original 5 Year factory warranty. This warranty will be consider null and void by BBE Sound, Inc. The equipment has been physically damaged. [. . . ]