Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual BEHRINGER CT100. We hope that this BEHRINGER CT100 user guide will be useful to you.
Lastmanuals help download the user guide BEHRINGER CT100.
Detailed instructions for use are in the User's Guide.
[. . . ] CT100
Users Manual
Version 1. 0 April 2001
CABLE TESTER
www. behringer. com
ENGLISH
CABLE TESTER CT100
1. With the CT100, you have purchased an indispensable tool that enables you to easily check the most common cables used by musicians and sound engineers. Faulty cables are a common cause of failure in live and studio situations. [. . . ] The LED will stay lit until RESET is pressed again, assuring detection of even the shortest breaks in the signal flow. It is a good idea to repeat the test after resetting the LEDs to double-check the initial results.
2
CABLE TESTER CT100
3. INSTALLED CABLE TESTER MODE
This mode enables you to test cables in fixed installations or situations that dont allow you to connect both ends of the cable to the CT100.
+
Hold down the RESET button while moving the ON switch to the CABLE TESTER position. The ON LED will blink to indicate that the CT100 is in INSTALLED CABLE TESTER MODE.
To test a cable for short circuits, connect one end of the cable to the appropriate OUT jack of the CT100. The display works as in CABLE TESTER MODE (see chapter 2). However, it now indicates connections between out pins. If no LEDs light, the cable is free of short circuits.
3. 1 Continuity check in INSTALLED CABLE TESTER MODE
For a continuity check, connect a shorting jack (a jack in which pins are short-circuited to one another) to the other end of the cable. If there are no breaks in the signal flow, the display will show the corresponding pins as being shorted to each other. If the display indicates no short circuit, there is a break in the signal flow.
+ +
The testing of intermittent connections works exactly as in CABLE TESTER MODE (see chapter 2. 1). INSTALLED CABLE TESTER MODE will not indicate connections between out and in pins. This is done in CABLE TESTER MODE (see chapter 2).
4. TEST TONE MODE
+ +
Move the ON switch to the position TEST TONE. Do not use the TEST TONE MODE for MIDI cables!
3
CABLE TESTER CT100
TEST TONE MODE may be used to check signal flow and to facilitate level adjustments. It routes a test tone to the + pin (pin 2/tip) of all OUT jacks. Use the TEST TONE LEVEL switch to choose between +4 dBu, -10 dBV, or -50 dBV mic level. Please note that this mode is not intended to work as a voltage standard and that battery voltage will affect the test tone output level.
4. 1 Selection between 1 kHz and 440 Hz
While in TEST TONE MODE, pressing RESET toggles between 1 kHz and 440 Hz. [. . . ] BEHRINGER Spezielle Studiotechnik GmbH, Hanns-Martin-Schleyer-Str. 36-38, 47877 Willich-Münchheide II, Germany Tel. +49 (0) 21 54 / 92 06-0, Fax +49 (0) 21 54 / 92 06-30
6 [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BEHRINGER CT100
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual BEHRINGER CT100 will begin.
