User manual BEHRINGER DDX3216

[. . . ] Version 1. 1 November 2001 www. behringer. com ENGLISH OPERATING MANUAL SAFETY INSTRUCTIONS DETAILED SAFETY INSTRUCTIONS: All the safety and operation instructions should be read before the appliance is operated. Retain instructions: The safety and operating instructions should be retained for future reference. Heed warnings: All warnings on the appliance and in the operating instructions should be adhered to. CAUTION: To reduce the risk of electric shock, do not remove the cover (or rear). No user serviceable parts inside; refer servicing to qualified personnel. Follow instructions: All operation and user instructions should be followed. [. . . ] Positive and negative values produce contrasting flanging characters!LFO Speed (0. 05 to 20 Hz) The LFO Speed parameter controls the speed (frequency) of the modulating signal. Feedback-LP (200 Hz to 20 kHz) Feedback-LP adjusts the cutoff frequency of a low-pass filter acting on the feedback signal. Mod Depth (0 to 100%) This parameter determines the modulation depth, i. Mod Delay (0. 5 to 50 ms) Mod Delay controls the delay of the modulated signal. Stereo Phase (45, 90 and 180°) This parameter determines the phase shift of the modulating waveform between the left and right channels. 5. EFFECTS PROCESSORS 27 5. 2. 13 Stereo Phaser A phaser is a phase shifter with LFO modulated phase shift. The resulting phase shift is called comb filter effect. When phasing is applied to an audio signal, the signal becomes "thicker" in texture and more lively in character, an effect that is often used for guitar sounds and keyboard pads, and had its heyday in the 70's, when phasers were standard devices for electric pianos. 5. 2. 15 Delay The Delay algorithm allows you to delay the input signal by as much as 1. 8 s. Use it to create rhythmic patterns. Fig. 5. 16: Parameters of Delay algorithm Delay (0 to 1, 800 ms) This parameter controls the delay time for the effect channel. 5. 14: Parameters of Stereo Phaser algorithm Stages (2 to 10) Stages determines the number of phase-shift stages. Speed (0. 1 to 10 Hz) This parameter controls the LFO frequency and thus the modulation speed. Depth (0 to 100%) This parameter governs the modulation depth, i. the amplitude of the modulating oscillation. Feedback (-99 to +99%) The Feedback parameter feeds some of the output signal back to the input. Stereo Phase (0 to 180°) This parameter determines the phase shift of the modulating waveform between the left and right channels. Feedback (0 to 99%) Feedback controls the number of repetitions. Feedback-HP (20 Hz to 10 kHz) This parameter controls the cutoff frequency of a high-pass filter acting on the feedback signal. Feedback-LP (100 Hz to 20 kHz) Feedback-LP adjusts the cutoff frequency of a low-pass filter acting on the feedback signal. 5. 2. 16 Flanger This algorithm provides a mono version of the Stereo Flanger algorithm (see chapter 5. 2. 12). 5. 2. 14 Pitch Shifter This effect varies the pitch of the input signal. Small values (cents) produce a subtle detune effect, but the pitch can also be shifted in semitones. The input signal can be transposed up and down by one octave. [. . . ] This also applies to defects caused by normal wear and tear, in particular, of faders, potentiometers, keys/buttons and similar parts. Damages/defects caused by the following conditions are not covered by this warranty: s misuse, neglect or failure to operate the unit in compliance with the instructions given in BEHRINGER user or service manuals. s connection or operation of the unit in any way that does not comply with the technical or safety regulations applicable in the country where the product is used. s damages/defects caused by force majeure or any other condition that is beyond the control of BEHRINGER. [. . . ]